OME-DB-24P/24PD Isolated Input Board | Omega OME-PIO-D144 specification

2.6.5OME-DB-24P/24PD Isolated Input Board

The OME-DB-24P is a 24 channel isolated digital input daughter board. The optically isolated inputs of the OME-DB-24P consist of a bi-directional opto-coupler with a resistor for current sensing. You can use the OME-DB-24P to sense DC signal from TTL levels up to 24V or use the OME-DB-24P to sense a wide range of AC signals. You can use this board to isolate the computer from large common-mode voltage, ground loops and transient voltage spike that often occur in industrial environments.

OME-PIO-D144

OME-PIO-D144

CN2CN6

50-Pin cable

AC or DC Signal 0V to 24V

V+

V-

Opto-Isolated

OME-DB-24P

	OME-DB-24P		OME-DB-24PD
50-pin flat-cable header	Yes		Yes
D-sub 37-pin header	No		Yes
Other specifications		Same

OME-PIO-D144 User’s Manual (Ver.2.1, Sep/2001)

----- 15

Image 17

Omega OME-PIO-D144 manual OME-DB-24P/24PD Isolated Input Board, OME-DB-24P OME-DB-24PD

Contents

User’sGuide Mexico CanadaBenelux Czech Republic OME-PIO-D144 Table of Contents Demo Program Product Check List SpecificationsAll signals are TTL compatible Board Layout Hardware configuration Refer to DEMO1.C for demo program Enable I/O OperationI/O Port Location O Architecture Make sure the initial level is High or Low If INT signal is Low now Æ select the non-inverted inputInterrupt Operation Refer to DEMO3.C for source code Refer to DEMO4.C for source code CN1PC0 CN1PC1 CN1PC2 CN1PC3 If PC1 is active OME-DB-37 Daughter BoardsOME-DN-37 & OME-DN-50 OME-DB-8125 OME-ADP-37/PCI & OME-ADP-50/PCI OME-DB-24P OME-DB-24PD OME-DB-24P/24PD Isolated Input BoardOME-PIO-D144 OME-DB-24R/24RD Relay Board COM OME-DB-24PR OME-DB-24PR/24POR/24COME-DB-24PR Daughter Board Comparison Table GND Pin AssignmentVCC OME-PIO-D144 User’s Manual Ver.2.1, Sep/2001 Resource-allocated information How to Find the I/O AddressPIO/PISO identification information PC’s physical slot information OME-PISO-P32C32 OME-PIO-821OME-PISO-P32A32 OME-PISO-P8R8 PIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux PIODriverInit PIOGetConfigAddressSpace ShowPIOPISO Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07 Assignment of I/O Address OME-PIO-D144 User’s Manual Ver.2.1, Sep/2001 RESET\ RESET\ Control RegisterI/O Address Map Address Read Write AUX data Register AUX Control RegisterINT Mask Control Register CN1PC3 CN1PC2 CN1PC1 CN1PC0 Interrupt Polarity Control Register Aux Status Register Active I/O Port Control Register Read/Write 8-bit data Register CN2PC CN2PB CN2PA CN1PC CN1PB CN1PA 9 I/O Selection Control RegisterCN4PC CN4PB CN4PA CN3PC CN3PB CN3PA CN6PC CN6PB CN6PA CN5PC CN5PB CN5PA \TC\LARGE\LIB\ \TC\LARGE\\TC\LARGE\DEMO?\ \TC\LARGE\LIB\PIO.H OME-PIO-D144.H Demo1 Use D/O of CN1 CN3 CN4 Demo2 Use D/O of CN1~CN6 PA/PB/PC COUNT=0 Demo3 Interrupt demo1 Refer to Sec .5.1 for more information Demo4 Interrupt demo2 Refer to Sec .5.2 for more information Demo5 Interrupt demo3 CN1PC1 OME-PIO-D144 User’s Manual Ver.2.1, Sep/2001 Demo 6 Outport of CN1-CN6 OME-PIO-D144 User’s Manual Ver.2.1, Sep/2001 Demo10 Find Card Number OME-PIO-D144 User’s Manual Ver.2.1, Sep/2001 WARRANTY/DISCLAIMER Temperature