Playback

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Playing the Connected Component

Operating with the remote controller

INPUT SELECTOR

RECEIVER

VOL q/w

Listening mode buttons

1

Press RECEIVER followed by an INPUT

 

SELECTOR button.

2

Start playback on the source component.

 

See also:

 

“Playing an iPod/iPhone via USB” (page 22)

 

“Playing a USB Device” (page 23)

 

“Listening to AM/FM Radio” (page 24)

 

“iPod/iPhone Playback via Onkyo Dock”

 

(page 46)

 

“Controlling Other Onkyo Components”

 

(page 48)

3

To adjust the volume, use VOL q/w.

4

Select a listening mode and enjoy!

See also:

“Using the Listening Modes” (page 26)

En-20

Turning On & Basic Operations

Operating on the AV receiver

Input selector buttons

 

LISTENING MODE

 

 

 

 

MASTER VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Use the input selector buttons to select the input

 

source.

2

Start playback on the source component.

3

To adjust the volume, use the MASTER VOLUME

 

control.

4

Select a listening mode and enjoy!

Page 20
Image 20
Onkyo HT-RC430 instruction manual Playback, En-20, Playing the Connected Component