Troubleshooting
If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer.
If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.
ON/STANDBY
VCR/DVR
Note that resetting the AV receiver will delete your radio presets and custom settings.
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video or
Power
Can’t turn on the AV receiver
•Make sure that the power cord is plugged into the wall outlet properly.
•Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it back in again.
The AV receiver turns off as soon as it’s turned on
•The amp protection circuit has been activated. Remove the power cord from the wall outlet immedi- ately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord discon- nected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer.
Audio
There’s no sound or it’s very quiet
•To listen to an audio source that’s connected to an HDMI input, make sure that input is assigned to an input selector (page 46). HDMI audio is passed through the AV receiver and can only be heard from your TV.
•To listen to an audio source that’s connected to an OPTICAL or COAXIAL input, make sure that input is assigned to an input selector (page 47).
•Make sure that speaker A or B is on (page 7).
•Make sure that all audio connecting plugs are pushed in all the way (page 26).
•Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with the metal part of each speaker terminal (page 21).
•Make sure that the speaker cables are not shorting.
•Check the volume (page 50). The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment.
•If the MUTING indicator is flashing on the display, press the remote controller’s [MUTING] button to unmute the AV receiver (page 51).
•While a pair of headphones is connected to the PHONES jack, no sound is output by the speaker set A and B (page 52).
•Check the digital audio output settings on the source component. On some game consoles, such as those that can play DVDs, the default setting is off.
•With some
•If your turntable doesn’t have a phono preamp
•If your turntable uses an MC cartridge, you must con- nect an MC head amp, or an MC transformer and a phono preamp.
•Check the speaker settings (pages
•If the digital signal format is set to PCM or DTS, set it to Auto (page 53).
•If there’s no sound from a DVD player connected to an HDMI IN, check the DVD player’s output settings, and be sure to select a compatible audio format.
Only the front speakers produce sound
•When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.
•Check the Speaker Configuration (page 74).
Only the center speaker produces sound
•If you use the Dolby Pro Logic IIx Movie or Dolby Pro Logic IIx Music listening mode with a mono source, such as an AM radio station or mono TV pro- gram, the sound will be concentrated in the center speaker.
•Check the Speaker Configuration (page 74).
The center speaker produces no sound
•When the Stereo or Mono listening mode is selected, the center speaker produces no sound (page 66).
•Check the Speaker Configuration (page 74).
The surround speakers produce no sound
•When the Stereo or Mono listening mode is selected, the surround speakers produce no sound.
•Depending on the source and the current listening mode, not much sound may be produced by the sur- round speakers. Try another listening mode (page 59).
•Check the Speaker Configuration (page 74).
92
