Manuals / Brands / Home Audio / MiniDisc Player / Onkyo / Home Audio / MiniDisc Player

Onkyo MD-101A Cause, Other, Remedy, Symptom, Information, Condensation, If the MD recorder is exposed to dew condensation

1 52

Download 52 pages, 1.5 Mb

Troubleshooting (Continued)

Symptom	Cause		Remedy

The disc name or track	•	The disc is record-protected	•	Close the record-protect tab. (See
name cannot be entered.		(“Protected” appears).		page 34.)
	•	A premastered (read-only) disc is	•	Replace it with a recordable disc.
		inserted (“Cannot Rec” appears).

System function cannot be	•	The system functions cannot be	•	Check all cable connections. The
used.		used.		system functions cannot be used
				even if remote control (		)
				even if remote control (		)
				cables are connected. Also
				connect the components using
				audio cables.
			•	If the symptom still persists,
				disconnect the power cord plug,
				then connect the plug again. If this

does not improve the condition, with the power cord plug connected, press and hold down the button for more than five seconds and operate the unit.

•Excessive electrical interference may temporarily render this system‘s sensitive microcomputer inoperable. If this happens, unplug the system for at least five seconds.

Condensation

This is the same phenomena that causes windows to mist with water in a heated room during the winter.

The MD recorder also sometimes gets dew (water drops) on the optical lens inside the player under the following conditions.

•Immediately after you turn a heater on.

•If the MD recorder is placed in a room full of steam or dampness.

•If you suddenly bring the MD recorder from the cold outside into a warm room.

If the MD recorder is exposed to dew condensation

You can leave it as it is. Sometimes the recorder cannot read the disc signal by laser and the recorder will not work.

Depending on the surrounding conditions, you can remove the disc and leave the power on for one

hour at most. The dew will evaporate and the recorder will work properly. If it doesn't work after Other several hours, please consult the nearest Onkyo authorized service center.

Information

47

Contents

Instruction Manual English using Before Connections Information Other Thank you for purchasing WARNING AVIS Read Instructions – Retain Instructions – Heed Warnings – 4.Follow Instructions – All operating and use instructions should be followed Water and Moisture – Precautions For U.S. model FCC INFORMATION FOR USER For Canadian model NOTE: CAUTION: For European model For British model IMPORTANT Table of contents Supplied accessories Using the remote controller •Auto Power On •Direct Change •Remote control of the System Components •Program Timer •Sleep Timer Connecting to the other components Connections Audio connection cable cable Amplifier CD player Connecting the () controller CD recorder Connecting the AC power cord (mains lead) Insert the AC power cord into a wall outlet. The STANDBY indicator lights Tuner/Amplifier Normal play Changing the display mode When the MD recorder is stopped When an MD is playing or pausing If the track name is too long to display Selecting the track to play using the number buttons To select a track numbered 26 or above using RC-475MD To select a track numbered 11 or above using RC-466S To play the next track or a later track Music Scan Random play RANDOM Repeat play Memory play MEMORY A. SPACE CD-dubbing(System operation) CD Dub Mode Fade Album 6 Press the CD DUBBING button on the MD-101A To stop the recording Tip: CD-dubbingwith track specified 1 Play a CD Recording 6 Press the REC button 7 Using the MULTI JOG knob, adjust the recording level 8 Press the button and then start playing the recording source immediately To manually record a track number To stop recording temporarily To stop recording To eject the MD Digital recording About digital recording If “D. In Unlock” appears 7 Adjust the recording level To stop recording temporarily To stop recording To eject the MD Using the Level Sync function To disable the auto numbering (Level Sync) function 3 Press the MULTI JOG knob To enable the auto numbering (Level Sync) Signal Synchro recording System operation Synchro-recordingfrom or CD recorder to MD 1 Press the INPUT button repeatedly until “Analog In” appears 3 Set the MD recorder to the recording standby mode 4 Start playing the CD recorder To stop synchro recording Timer operation 2 Press the INPUT button repeatedly until “Analog In” 1 Insert an MD appears 4 Set the timer on your R-801A Other information for recording Editing the contents of an MD To erase all tracks of an MD Dividing a track 1 Pause a track at the desired dividing point 2 Press the EDIT/NO button and turn the MULTI JOG knob to select “Divide ?” 4 Fine-adjustthe dividing point 5 Divide the track Combining tracks (Combine function) 2 Press the EDIT/NO button and turn the MULTI JOG knob to select “Combine ?” To cancel the Combine operation 5 When the combining operation is completed, “Complete” appears on the display 4 Press the MULTI JOG knob again Moving a track 1 Turn the MULTI JOG knob until the track number you want to move is displayed 2 Press the EDIT/NO button and turn the MULTI JOG knob to select “Move ?” 4 Press the MULTI JOG knob to move the selected track To stop moving a track Naming a track or disc 4 Select the character input mode using the DISPLAY button 5 Enter a track name or disc name using the MULTI JOG knob To change the type of characters entered To correct the character entered To insert a character 6 Press the YES button Erasing the disc name and all track names at one time 1 Press the STOP button Preset names for easy naming Message list System limitations Rules for digital recording Troubleshooting Remedy Condensation If the MD recorder is exposed to dew condensation Other Information Precautions for handling the MiniDisc (MD) Indexed to parts and controls Remote controller Page Specifications