Onkyo TX-DS797 instruction manual Audio Adjust Setup menu

Audio Adjust

3. Audio Adjust Setup menu

Set the various parameters for the sound signals.

Surround L/R: This outputs the sound to the surround left and right speakers as normal and outputs nothing to the surround back speaker.

Advanced Menu

3.Audio Adjust

1.Tone Control

2.Surround Speakers

3.Sound Effect

4.Delay

5.LFE Level

6.Mono Setup

7.Theater-Dimensional

8.Surround Setup

Advanced Menu

3.Audio Adjust

9.THX Setup

10.Mono Movie Setup

11.Enhanced 7 Setup

12.Orchestra Setup

13.Unplugged Setup

14.Studio Mix Setup

15.TV Logic Setup

→default

Basic Menu

3.Audio Adjust

1.Tone Control

2.Surround Speakers

3.Sound Effect

→default

Surround Back: This outputs the sound to the surround back speakers and outputs nothing to the surround left and right speakers.

Sur L/R+Back: This outputs the sound to both the surround left and right speakers and the surround back speaker.

Note:

If the Surr Back Out setting in the Speaker Config sub menu is set to “1ch,” the Surround Speakers sub menu is disabled.

3-3. Sound Effect

Turn on and off the various sound effects.

		Parameter	Setting
			Initial value
a	RE-EQ	On, Off	Off
b	Upsampling	On, Off	Off
c	Subwoofer	On, Off	On
	(Ana/PCM)
d	Late Night	Off, Low, High	Off

a) Re-EQ

Re-EQ (re-equalization) takes the edginess or “brightness” out of your home cinema sound to compensate for the fact that sound mixed for theaters may sound too bright when played back through speakers in the home environment.

3-1. Tone Control

Separately adjust the bass and treble settings as desired in 2-decibel units.

Advanced Menu

3.Audio Adjust

3-1.Tone Control
a.Bass	:	0
b.Treble	:	0
	Quit:SETUP

		Parameter	Setting
			Initial value
a	Bass	–12 to +12	0
b	Treble	–12 to +12	0

Note:

If DIRECT or THX is selected as the listening mode, these settings cannot be made. To make these settings, first select another listening mode.

3-2. Surround Speakers

This setting allows you to decide which speakers to output to when surround back speakers are connected and you are playing back a 5.1-channel source.

Parameter	Setting
	Initial value
a Surround Speakers Surround L/R, Surround Back,	Surround L/R
Surr L/R + Back

This can be set to either “On” or “Off.”

This parameter is enabled for listening modes other than the THX, T-D, Direct, PL II Music, or Neo:6 Music listening mode.

b) Upsampling

Upsampling processes the input digital signal, or the digital signal converted from an analog input source, and converts its digital sampling frequency to twice its current frequency for an even further detailed sound reproduction. This can be set to either “On” or “Off.” When “On” is selected, the UPSAMPLING indicator lights.

c) Subwoofer

When “Yes” is selected for the Subwoofer setting in the Speaker Config sub-menu, set this to “Off” if you do not want to have sound output from the subwoofer. This setting is only effective when the input source is Analog/PCM. If “No” is selected for the Subwoofer setting in the Speaker Config sub-menu, then this setting will not appear.

d) Late Night

Cinema sound has a vast dynamic range; therefore, to hear the quieter sounds such as human conversations, they must be played back at larger volumes. When this parameter is set to “High” or “Low,” the dynamic range of the sound is narrowed down to allow you to easily hear minute sounds at low volumes. This function is especially useful if you wish to play a movie at low volumes during the nighttime.

This can be set to either “Off” or “Low,” or “High.”

When this parameter is set to High or Low, the dynamic range of the sound is narrowed down to allow you to easily hear minute sounds at low volume.

Off: Turns off the Late Night function.

Low: Lowers the dynamic range.

High: Narrows down the dynamic range.

Notes:

•The Late Night function is effective only on Dolby Digital encoded software.

•The depth of the Late Night effect is determined by Dolby Digital software. Some sounds may produce no or little effect.

40