Onkyo TX-NR5007 Remote Controller

14

Remote Controller

Notes:

• If the remote controller doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old batteries or different types of

batteries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent damage from

leakage or corrosion.

• Expired batteries should be removed as soon as possi-

ble to prevent damage from leakage or corrosion.

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

Transmission

Received

Notes:

• The remote controller may not work reliably if the AV

receiver is subjected to bright light, such as direct sun-

light or inverter-type fluorescent lights. Keep this in

mind when installing.

• If another remote controller of the same type is used in

the same room, or the AV receiver is installed close to

equipment that uses infrared rays, the remote control-

ler may not work reliably.

• Don’t put anything, such as a book, on the remote con-

troller, because the buttons may be pressed inadvert-

ently, thereby draining the batteries.

• The remote controller may not work reliably if the AV

receiver is installed in a rack behind colored glass

doors. Keep this in mind when installing.

• The remote controller will not work if there’s an

obstacle between it and the AV receiver’s remote con-

trol sensor.

• When the remote control codes have been registered

and you want to operate another component

(page 141), or when you want to operate an Onkyo

component without connection, point the remote

controller at the other component to use it.

• When you want to operate an Onkyo component with

connection or an -compatible compo-

nent connected via HDMI (pages 143 and 144), point

the remote controller at the AV receiver’s remote con-

trol sensor.

Installing the Batteries

1To open the battery compartment, press

the small lever and remove the cover.

2Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram

inside the battery compartment.

3Replace the cover and push it shut.

Aiming the Remote Controller

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

30° off center

(Left/Right/Up/Down)

15

15

Transmitter

AV receiver

Approx. 16 ft. (5 m)

Incoming sensor

15° off center

(Left/Right/Up/Down)

Contents

Main E n AV Receiver TX-NR3007 TX-NR5007 Instruction Manual Contents Important Safety Instructions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: WARNING Precautions For U.S. models For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS CAUTION: TO PREVENT ELECTRIC SHOCK, Supplied Accessories Make sure you have the following accessories: * Declaration of Conformity Power cord (Plug type varies from country to country.) Contents Introduction * Basic Operations Connection Features Amplifier Processing Connections Miscellaneous FeaturesContinued Front & Rear Panels Front Panel Page Display Rear Panel Page Page Remote Controller Installing the Batteries 3 1 2 Remote ControllerContinued Controlling the AV Receiver Page About Home Theater Enjoying Home Theater Connecting the AV receiver About Speakers A and Speakers B Connecting Your Speakers Speaker Configuration Attaching the Speaker Labels Connecting Powered Subwoofers Using Dipole Speakers Speaker Connection Precautions Connecting the Speaker Cables 1 2 4 Page Bi-amping Speaker Hookup Bi-amping the Front Speakers A 1 2 3 4 Bridged Speaker Hookup 1 2 Bi-amping Speaker Hookup Bi-amping the Front Speakers B 1 2 3 4 Bridged Speaker Hookup 1 2 Connecting the Indoor FM Antenna Connecting the AM Loop Antenna Connecting Antenna 1 2 1 2 Connecting an Outdoor FM Antenna Connecting an Outdoor AM Antenna Optical Digital Jacks AV Connection Color Coding AV Cables & Jacks About AV Connections About HDMI Supported Audio Formats About Copyright Protection Connecting Components with HDMI Making HDMI Connections Video Connection Formats Connecting Both Audio & Video Which Connections Should I Use? Page Audio Connection Formats * Connecting a TV or Projector Connecting a DVD Player Hooking Up the Multichannel Input 5.1 ch 7.1 ch Connecting a VCR or DVD Recorder for Playback Hint! Connecting a VCR or DVD Recorder for Recording Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source Connecting a Game Console Choose an audio connection that matches your game console ( or ), and then make the connection. Connecting a Camcorder or Other Device Make the connection . A b Choose an audio connection that matches your camcorder ( or ), and then make the connection. a Connecting a CD Player or Turntable a b c Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches the recorder ( , or ), and then make the connection. c a a b Connecting a Power Amplifier Connecting an RI Dock Connecting a Universal Port Option Series Connecting Onkyo Components Connecting the Power Cord Turning On the AV receiver Turning On and Standby 1 2 Smooth Operation in a Few Easy Steps First Time Setup Monitor Setup 1 2 Selecting the Language used for the onscreen setup menus Onscreen Setup Menus and Display Using the Onscreen Setup Menus Using the Display to change the settings Monitor Out Setup 6 HDMI Input Setup Video Input Setup Component Video Input Setup Digital Audio Input Setup Analog Audio Input Setup 1 4 Speaker Settings 1 Powered Zone 2/3 6 7 TV Format Setup (European and Asian models) FM/AM Frequency Step Setup 4 Changing the Input Display 1 2 Measurement Positions Audyssey MultEQ XT Room Correction and Speaker Setup Using Audyssey MultEQ XT 1 2 3 4 5 6 7 8 9 10 11 One of the front speakers has not been detected. One of the front wide speakers has not been detected. One of the front high speakers has not been detected. One of the surround speakers has not been detected. The surround back speakers have been detected but the surround speakers havent. Changing the Speaker Settings Manually Using Powered Subwoofers Basic Operations Selecting the Input Source 1 2 3 Adjusting the Bass & Treble Displaying Source Information Setting the Display Brightness Muting the AV Receiver Using the Sleep Timer Front High or Front Wide Speakers Speakers A or Speakers B Configuration Selecting Speaker Layout Using Headphones Using Easy Macros 1 2 Changing Source Component Restoring Default Listening to the Radio Listening to the Radio Tuning into Radio Stations Using the Tuner 1 1 2 3 4 1 2 RDS Program Types (PTY) Using RDS (European models) Displaying Radio Text (RT) Finding Stations by Type (PTY) Listening to Traffic News (TP) 1 2 3 4 1 2 Universal Port Option UP-A1 Dock for iPod About the UP-A1 Dock Compatible iPod models Function Overview Universal Port Option UP-A1 Dock for iPodContinued Controlling iPod Universal Port Option UP-A1 Dock for iPodContinued Status messages Recording AV Recording Recording Separate AV Sources 1 2 Using the Listening Modes Selecting on the AV receiver Selecting with the Remote Controller Selecting Listening Modes Mono/Multiplex Sources Listening Modes Available for Each Source Format Stereo Source (1/2) Stereo Source (2/2) 5.1 channel Sources (1/3) 5.1 channel Sources (2/3) 5.1 channel Sources (3/3) Listening Mode Button Speaker layout T-D (Theater- Dimensional) DTS Surround Sensation 7.1 channel Sources About the Listening Modes Page Onkyo Original DSP Modes Advanced Setup page 116 page 109 Submenus 3. Audio Adjust Input/Output Assign Page Speaker Setup 1 2 3 4 5 Page Page 1 2 3 Page Audio Adjust Page Page Page Source Setup 1 2 3 4 5 1 2 Page Page Page Assigning Listening Modes to Input Sources Miscellaneous (Volume/OSD) Setup . Hardware Setup 1 2 Page Page Page Lock Setup 1 2 3 4 Digital Input Signal Formats 1 2 Using the Audio Settings 1 2 3 Page Page NET/USB Network Requirements About NET Connecting the AV Receiver Listening to Internet Radio 1 2 3 Playing Music Files on a Server 1 2 3 4 5 1 2 3 4 5 Supported Audio File Formats Server Requirements About DLNA Network Settings 1 2 3 4 5 About USB DHCP IP Address Subnet Mask Gateway 1 2 3 4 Page Multi Zone Multiroom Capability Main Room Zone 2 Room Zone 3 Room Connecting Zone 2 Zone 2 Video Output Zone 2 12V Trigger Connecting Your Zone 3 Speakers Directly to the AV receiver Connecting Your Zone 3 Speakers to an Amp in Zone 3 Zone 3 12V Trigger Connecting Zone 3 Setting the Powered Zone 2/3 1 2 3 4 Setting the Multi Zone 1 2 3 4 Controlling Zone 2/3 from the AV receiver 1 2 3 Adjusting the Volume for Zones Muting Zones 2 3 Using a Multiroom Kit with Zone 2/3 Using a Multiroom Kit with a Cabinet Using a Multiroom Kit with Other Components Using the Remote Controller in Zone 2/3 and Multiroom Control Kits Controlling Other Components Preprogrammed Remote Control Codes Looking up for Remote Control Code 6 7 8 9 Entering Remote Control Codes 1 2 3 Remote Control Codes for Onkyo Components Connected via 1 2 3 Resetting REMOTE MODE Buttons 2 Controlling a TV Controlling a DVD Player or DVD Recorder Controlling a VCR or PVR Controlling a Satellite Receiver or Cable Receiver Controlling a CD Player, CD Recorder or MD Recorder Controlling an RI Dock Controlling a Cassette Recorder Activities Setup 6 7 8 9 Learning Commands 2 3 4 Making Macros Running Macros 2 3 2 Troubleshooting Page Page Page Page Page Specifications (TX-NR3007) Amplifier Section Video Section Tuner Section General Specifications (TX-NR5007) Amplifier Section Tuner Section Video Section General Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver. NTSC PAL Page * 2 9 4 0 0 0 5 9 *