Onkyo TX-NR636 manual  4th Step Network Connection,  Exiting the setup wizard, Setting button

4th Step : Network Connection

Initial Setup

Network Connection

Do you want to connect network connection? It gives you network services that our AV receiver support. If you wish to skip this step. select “No. Skip”.

Yes

No. Skip

HOME Exit

You can check the network connection and make the Wi-Fi setting. When the Network Connection start screen is displayed, select "Yes" with the cursors and press ENTER on the remote controller. If you select "Wired" in the next screen, you can view the LAN cable connection status. To make the Wi-Fi setting, select "Wireless", press ENTER on the remote controller and follow the sections below.

Make the following preparations.

Wi-Fi connection requires an access point such as wireless LAN router (Ú). Write down the SSID and password (key) of the access point if they are shown in the label of the main body. If the access point has an automatic setting button (may be called differently according to the manufacturer), you can set up without inputting the password. For how to use the automatic setting button of the access point, refer to its instruction manual.

¼¼The unit supports Wi-Fi connection with 2.4 GHz access point.

1.Select the SSID of the access point to be connected with the cursor buttons and press ENTER.

When the SSID of the access point appears on the TV screen, select the desired access point.

•If you changed the initial setting of the access point to skip password entry, Step 3 starts automatically.

•If you changed the initial setting of the access point to hide the SSID, see "When the access point is not displayed".

2.Select and set the authentication method.

Wi-Fi Setup

Select the authentication method.

Enter Password

Push Button

PIN code

When the screen above is displayed, select and set one of the three authentication methods: "Enter Password", "Push Button" and "PIN code". See below for details of and how to set each method.

Enter Password: Enter the password of the access point to establish connection.

1 Select "Enter Password" with the cursor buttons and press ENTER.

2 Enter the password (Ú) on the keyboard screen, select "OK" with the cursor buttons and press ENTER.

•The keyboard screen may be displayed automatically if the access point device does not have an automatic

setting button.

¼¼Select "Shift" and press ENTER to toggle between upper and lower case. Select "" or "" and press ENTER to move the cursor to the selected direction. Select "Back Space" and press ENTER to delete the character at the left of the cursor position. To select whether to mask the password with "*" or display it in plain text, press D on the remote control. Press + 10 on the remote controller to enable the "Shift" function and CLR to delete all the input characters.

3 If the security method of the access point to be connected is WEP, select "Default Key ID", select "OK" and press ENTER.

Push Button: Use the automatic setting button of the access point to establish connection.

1 Select "Push Button" with the cursor buttons and press

ENTER.

2 Hold down the automatic setting button of the access point for the necessary seconds, select "OK" with the cursor buttons and press ENTER.

PIN code: Select this method when the automatic setting button of the access point is beyond the reach. Select "PIN code" with the cursor buttons and press ENTER to display the 8-digit PIN code. Register the displayed PIN code to the access point, select "OK" with the cursor buttons and press ENTER. For how to register the PIN code to the access point, refer to its instruction manual.

Step 2: Setting Up

3.Establish connection.

The connection process starts and the Wi-Fi indicator on the left of the unit's display starts flashing. When connection has been established, the Wi-Fi indicator changes from flashing to staying lit. If the Wi-Fi indicator does not stay lit, connection has not been established. Make the setting again. If "Push Button" does not work, try "Enter Password".

When the access point is not displayed Select "Other..." with the c cursor on the remote controller and press ENTER to display the keyboard screen. Input the SSID and password. Make the following settings according to the router setting.

WPA/WPA2 method

Select "WPA" or "WPA2" in "Security Method", select "OK" and press ENTER.

WEP method

Select "WEP" in "Security Method" and select "Default Key ID". Then select "OK" and press ENTER.

•If encryption setting has not been made on the wireless LAN router, select "None" in "Security Method", select "OK" and press ENTER.

Exiting the setup wizard

After finishing the initial setup, keep "Finished" selected and press ENTER on the remote controller. Connection and setting of the unit is now completed. See Step 3 and enjoy your home theater.

9