If the input signal format is set to “PCM” or “DTS”. 44 Set it to “Off”.

Only the front speakers produce sound

When the Stereo or Mono listening mode is selected,

31

only the front speakers and subwoofer produce

 

sound.

 

 

 

Check the Speaker Configuration.

40

 

 

Only the center speaker produces sound

If you use the Dolby Pro Logic II Movie, Dolby Pro — Logic II Music, or Dolby Pro Logic II Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

Make sure the speakers are configured correctly.

40

The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

 

speakers produce no sound.

 

 

 

Depending on the source and current listening mode,

28

not much sound may be produced by the surround

 

speakers. Try selecting another listening mode.

 

Make sure the speakers are configured correctly.

40

The center speaker produces no sound

When the Stereo or Mono listening mode is selected, — the center speaker produces no sound.

Make sure the speakers are configured correctly.

40

The subwoofer produces no sound

The subwoofer outputs no sound while only Speakers

33

B is on. Turn on Speakers A.

 

 

 

When you play source material that contains no

information in the LFE channel, the subwoofer

 

produces no sound.

 

Make sure the speakers are configured correctly.

40

There’s no sound with a certain signal format

Check the digital audio output setting on the

connected device. On some game consoles, such as

 

those that support DVD, the default setting is off.

 

 

 

With some DVD-Video discs, you need to select an

audio output format from a menu.

 

Depending on the input signal, some listening modes

29-30

cannot be selected.

 

Can’t get 5.1 playback

When Speaker B is turned on, Speakers A is reduced

33

to 2.1-channel playback.

 

 

 

Depending on the number of connected speakers, it is

29-30

not always possible to select all of the listening

 

modes.

 

 

 

The speaker volume cannot be set as required

After the volume level of each individual speaker has 41 been adjusted, the maximum volume may be reduced.

Noise can be heard

Using cable ties to bundle audio cables with power

cords, speaker cables, and the like may degrade the

 

audio performance, so refrain from doing it.

 

 

 

An audio cable may be picking up interference. Try

repositioning your cables.

 

 

 

The Late Night function doesn’t work

Make sure the source material is Dolby Digital,

47

Dolby Digital Plus, or Dolby TrueHD.

 

Appendix

About DTS signals

When DTS program material ends and the DTS

bitstream stops, the AV receiver remains in DTS

 

listening mode and the dts indicator remains on. This

 

is to prevent noise when you use the pause, fast

 

forward, or fast reverse function on your player. If

 

you switch your player from DTS to PCM, because

 

the AV receiver does not switch formats

 

immediately, you may not hear any sound, in which

 

case you should stop your player for about three

 

seconds, and then resume playback.

 

With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast — forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

The beginning of audio received by an HDMI IN can’t be heard

Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio

 

signals, audio output may not start immediately.

 

En-55

Page 55
Image 55
Onkyo TX-SR313 instruction manual En-55