Audyssey 2EQ® Room Correction and | Note | |
Speaker Setup | • Make the room as quiet as possible. Background noise and Radio | |
| Frequency Interference (RFI) can disrupt the room measure- | |
With the supplied calibrated microphone, Audyssey 2EQ | ments. Close windows, televisions, radios, air conditioners, flu- | |
automatically determines the number of speakers con- | orescent lights, home appliances, light dimmers, or other | |
nected, their size for purposes of bass management, opti- | devices. Silence the cell phone (even if it is not in use) or place | |
mum crossover frequencies to the subwoofer (if present), | it away from all audio electronics. | |
• The microphone picks up test tones which played through each | ||
and distances from the primary listening position. | ||
speaker as Audyssey 2EQ Room Correction and Speaker Setup | ||
Audyssey 2EQ then removes the distortion caused by | ||
run. | ||
room acoustics by capturing room acoustical problems | ||
• Audyssey 2EQ Room Correction and Speaker Setup cannot be | ||
over the listening area in both the frequency and time | performed while a pair of headphones is connected. | |
domain. The result is clear, | 1 Turn on the AV receiver and the connected TV. | |
one. Enabling Audyssey 2EQ allows you to also use | ||
Audyssey Dynamic EQ™, which maintains the proper | On the TV, select the input to which the AV receiver | |
is connected. | ||
Before using this function, connect and position all of | 2 Set the speaker setup microphone at the Main Lis- | |
your speakers. | ||
If “Dynamic EQ” is set to “On” (➔ 39), the “Audyssey” | tening Position 1, and connect it to the SETUP | |
MIC jack. | ||
setting will be set to “Off” (➔ 38). On the other hand, if it | ||
| ||
is set to “Off”, the “Dynamic Volume” setting will be set | SETUP MIC jack | |
to “Off” (➔ 39). | Speaker setup | |
It takes about 15 minutes to complete Audyssey 2EQ | ||
microphone | ||
Room Correction and Speaker Setup for three positions. | ||
| ||
Total measurement time varies depending on the number |
| |
of speakers. |
|
Using Audyssey 2EQ
To create a listening environment in your home theater that all listeners will enjoy, Audyssey 2EQ takes measure- ments at up to three positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results.
aFirst measurement position
Also referred to as the Main Listening Position this refers to the most central position where one would normally sit within the listening environment. 2EQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.
bSecond measurement position The right side of the listening area.
cThird measurement position The left side of the listening area.
The distances from position a to b and a to c must be at least 1 meter.
TV
The speaker setting menu appears.
Note
•The
3 When you’ve finished making the settings, press
ENTER.
2EQ: Auto Setup |
| Audyssey |
|
|
|
|
|
|
| ||
Speakers Type | < Normal > | ||
Speaker Terminal Assign |
|
|
|
Front High/Zone2 | Front High | ||
SurrBk/FrontHigh | SurrBack | ||
If your front speakers are
4 Press ENTER.
Audyssey 2EQ Room Correction and Speaker Setup starts.
Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup.
: Listening area | a to c: Listening position | En |
23
