Onkyo TX-SR508 Error Messages, Changing the Speaker Settings Manually, Using a Powered Subwoofer

5 Place the setup microphone at the next position, and then press ENTER.

Audyssey 2EQ® performs more measurements. This takes a few minutes.

6 When prompted, place the setup microphone at the next position, and repeat step 5.

7 Use q/wto select an option, and then press

ENTER.

2EQ: Auto Setup				Audyssey
	<- Review Speaker Configuration ->
	Subwoofer	:	Yes
	Front	:	Small
	Center	:	Small
	Surround	:	Small
	Front High	:	Small
	Surr Back	:	Small
	Surr Back CH	:	2ch

Save

Cancel

The options are:

`Save:

Save the calculated settings and exit

Audyssey 2EQ Room Correction and Speaker

Setup.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

Note

•You can view the calculated settings for the speaker con- figuration, speaker distances, and speaker levels by using e/r.

8 Disconnect the speaker setup microphone.

Note

•When Audyssey 2EQ Room Correction and Speaker Setup is complete, the “Audyssey” will be set to “On” (➔ 38). The Audyssey indicator will light (➔ 8).

•You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

•Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

•If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

•Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correc- tion and Speaker Setup again, as room EQ characteristics may have changed.

En

Error Messages

While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup Audyssey

Ambient noise is too high. Error message

Retry

Cancel

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker matching error!

The number of speakers detected was different from that of the first measurement. Check the speaker con- nection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ 11).

Changing the Speaker Settings Manually

You can manually make changes to the settings found dur- ing Audyssey 2EQ Room Correction and Speaker Setup. See also:

•“Sp Config (Speaker Configuration)” (➔ 36)

•“Sp Distance (Speaker Distance)” (➔ 37)

•“Level Cal (Level Calibration)” (➔ 37)

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the vol- ume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the sub- woofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

24