Onkyo TX-SR573 instruction manual Learning Commands from Other Remote Controllers, Notes

Controlling Other Components—Continued

Learning Commands from Other Remote Controllers

The AV receiver’s remote controller can receive and learn commands from other remote controllers. By trans- mitting, for example, the Play command from your CD player’s remote controller, the remote controller can learn it and then transmit the exact same command when its Play [ ] button is pressed in CD mode.

3Point the remote controllers at each other, about 2 to 6 inches (5–15 cm) apart, and then press and hold the button whose com- mand you want to learn until the Remote indicator flashes.

If the command is learned successfully, the Remote indicator flashes twice.

You can also use this function to learn individual com- mands after entering a remote controller code (page 54).

			Remote
			indicator
ON	STANDBY		TV
1
		I	INPUT
V1	V2	V3
1	2	3	+
	MULTI CH	DVD	TV CH
4	5	6	-
CD	TAPE	TUNER
7	8	9

RECEIV APE/AMP ER

VCR

About 2 to 6 inches (5–15 cm)

ON

1

V1

STA

N

4

DBY

CD

2

V2

7

MULTI

I

+1

TAPE

5

CH

3

V3

TV

--/

0

8

DVD

INPUT

---

10

6

1

INP

UT

0

TU

T

+

S

CT

C

9

R

VC

2MACRO

11

-

H

ELE

LEAR

DVD REMOTE

3

OR

TV

VOL

12

MODE

CD

CABLE

HDD

RC-632M

CDR

MDSAT

CHT	PUIN
-I
ULTM

									R
							MELU
								OV
									G
									TIN
									UM
							E		L
							TSNO		EV
							ET T
								ELS	HC
		TE
D		SE				VD			EP
	C		RPR
			EN			D			AT
		O		UT
		NO			P
		RPH			UO
RED		TO	EC	R	RG
USOM				E		2-	DC	C
		R		ELSUNTT		OE		DIS
		MEM		UP		IDV
		DI			IN PEA		1-
			PE			T	EO
				EL		D	V
				S		VD
					R
					EW
					PO

						TV VOL
	+10		0	CLEAR
	- - / - - - 10		11		12
	INPUT SELECTOR
		MACRO
	1		2	3
		REMOTE MODE
1, 4	RECEIVER	DVD		CD		HDD
	TAPE/AMP
	TV	VCR		CABLE		SAT
				CDR		MD
	DIMMER					SLEEP
			NU	ME
		ME
		P		N
		O			U
		T
	+
	CH		ENTER			VOL
	DISC
	ALBUM
	-
	PREV	R			P
	CH	ET	URN		U
				SET
	DISPLAY					MUTING

1While holding down the REMOTE

REMOTE MODE		MODE button for the mode in
RECEIVER	DVD	which you want to use the com-
TAPE/AMP		mand, press the [ON] button.
CD	HDD
		The Remote indicator lights up.
TV	VCR
CABLE	SAT
CDR	MD

ON

2On the AV receiver’s remote con- troller, press the button you want to learn the new command.

4To learn more commands, repeat steps 2 and 3.

Press any REMOTE MODE button when you’ve finished.

Notes:

•The following buttons cannot learn new commands:

REMOTE MODE, MACRO [1], [2], [3], TV [ ],

TV CH [+]/[–], [TV INPUT], TV VOL []/[ ].

•The AV receiver’s remote controller can learn approx- imately 70–90 commands, although, this will be reduced by commands that use a lot of memory.

•Remote controller buttons such as Play, Stop, Pause, and so on are preprogrammed with commands for controlling Onkyo CD players, cassette decks, and DVD players. However, they can learn new com- mands, and you can restore the preprogrammed com- mands by resetting the remote controller (page 55).

•To overwrite a previously learned command, repeat this procedure.

•Only commands from infrared remote controllers can be learned.

•When the remote controller’s batteries expire, all learned commands will be lost and will have to be learned all over again, so don’t discard your other remote controllers.

57