Onkyo TX-SR804E instruction manual Learning Commands from Other Remote Controllers, Notes

TX-SR804/804E_En.book Page 89 Monday, September 4, 2006 9:34 AM

Controlling Other Components—Continued

Learning Commands from Other Remote Controllers

The AV receiver’s remote controller can receive and learn commands from other remote controllers. By trans- mitting, for example, the Play command from your CD player’s remote controller, the remote controller can learn it and then transmit the exact same command when its Play [ ] button is pressed in the CD remote mode.

3	Point the remote controllers at
	each other, about 2 to 6 inches
	(5–15 cm) apart, and then press
	and hold the button whose com-
	mand you want to learn until the
	Remote indicator flashes.
	If the command is learned successfully,
	the Remote indicator flashes twice.

You can also use this function to learn individual com- mands after entering a remote control code (page 86).

			Remote
			indicator
ON	STANDBY		TV
1
		I	INPUT
V1	V2	V3
1	2	3	+
V4	MULTI CH	DVD	TV CH
4	5	6	-
CD	TAPE	TUNER
7	8	9

	RE
P	CEIVER
E/AMP
	VCR
ME
	N
	U

About 2 to 6 inches (5–15 cm)

ON

1

V1

ST

AN

V4

DB

4

V2

Y

C

PHONO

7

D

MULTI

2

I

-

+

T

5

CH

V

TV

-/-

10

AP

3

3

-- 1

8

E

D

IN

1

0

0

TU

VD

PUT

INPUT

6

+

R

SELECTOR

CLEAR

NER

T

2MACRO

11

9

-

H

VC

DVD

EMO

1

T

TE

MO

3

2

VV

OL

CD

DE

Z

C

ON

CDRABLE

HDD

E2

RC-620M

SLEEP

MDSAT

CH- INPUT MULTI

R

VOLUME

MUTING

TESTTONE

VEL

SEL

CH

PRESET

D

C

DVD

TAPE

PHONO

TUNER

GROUP

SURMODE

NER

2-

DC

DISC

ER

SELECTOR TU

VIDEO

DIMM

INPUT TAPE

1-

SLEEP

DVD

VIDEO

POWER

	PHONO						TV VOL
	+10		0	CLEAR
	- - / - - - 10		11			12
	INPUT SELECTOR
		MACRO
	1		2	3			ZONE2
		REMOTE MODE
1, 4	RECEIVER	DVD		CD			HDD
	TAPE/AMP
	TV	VCR		CABLE			SAT
				CDR			MD
	DIMMER						SLEEP
			NU	ME
		ME			N	U
		P
		O
		T
	+
	CH		ENTER				VOL
	DISC
	ALBUM
	-
	PREV	R				P
	CH	ET	URN		U
				SET
	DISPLAY						MUTING

4	To learn more commands, repeat
	steps 2 and 3.
	Press any REMOTE MODE button
	when you’ve finished.

Notes:

•The following buttons cannot learn new commands:

REMOTE MODE, MACRO [1], [2], [3], TV [ ],

TV [INPUT], TV CH [+]/[–], TV VOL []/[ ], Light.

•	The remote controller can learn approximately 70-90
	commands, although, this will be reduced by com-
	mands that use a lot of memory.
•	Remote controller buttons such as Play, Stop, Pause,

1

REMOTE MODE

RECEIVER DVD TAPE/AMP

CD HDD

TV VCR

CABLE SAT

CDR MD

ON

While holding down the REMOTE MODE button for the mode in which you want to use the com- mand, press the [ON] button.

The Remote indicator lights up.

and so on are preprogrammed with commands for

controlling Onkyo CD players, cassette decks, and

DVD players. However, they can learn new com-

mands, and you can restore the preprogrammed com-

mands by resetting the remote controller (see

page 87).

• To overwrite a previously learned command, repeat

this procedure.

• Only commands from infrared remote controllers can

be learned.

• When the remote controller’s batteries expire, all

learned commands will be lost and will have to be

learned all over again, so don’t discard your other

remote controllers.

2	On this AV receiver’s remote con-
	troller, press the button you want
	to learn the new command.

89