Onkyo TX-SR804E Advanced Setup, Speaker Setup, Speaker Configuration, nected, None

TX-SR804/804E_En.book Page 70 Monday, September 4, 2006 9:34 AM

Advanced Setup

Speaker Setup

This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.

Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 40).

2		Use the Up and Down [ ]/[ ]
		buttons to select “3. Speaker
		Setup,” and then press [ENTER].
	ENTER	The Speaker Setup menu appears.

ENTER

	V4	MULTI CH	DVD		TV CH
	4	5	6		-
	CD	TAPE	TUNER
	7	8	9
	PHONO				TV VOL
	+10	0	CLEAR
	- - / - - - 10	11		12
	INPUT SELECTOR
		MACRO
	1	2	3		ZONE2
RECEIVER		REMOTE MODE
	RECEIVER	DVD	CD		HDD
	TAPE/AMP
	TV	VCR	CABLE		SAT
			CDR		MD
	DIMMER				SLEEP
		U	ME
		MEN		NU
		OP
		T
ENTER	+
	CH	ENTER			VOL
	DISC
	ALBUM
	-
	PREV	RE		P	SETUP
	CH	TURN	SETU
	DISPLAY				MUTING
	REC	PLAYLIST			RANDOM
		LISTENING MODE

3

ENTER

ENTER

Use the Up and Down []/[ ] buttons to select “Speaker Con- figuration,” and then press [ENTER].

The Speaker Config menu appears.

3-2.Speaker Config

------------------------

a.Subwoofer		:Yes
b.Front	:80Hz(THX)
c.Center	:80Hz(THX)
d.Surround	:80Hz(THX)
e.SurrBack	:80Hz(THX)
f.SurrBack Ch		:2ch
g.LPF of LFE
	:80Hz(THX)
h.Subwoofer Mode
:-------------

STEREO	SURR
REPEAT	AUDIO	SUBTITLE	PLAY MODE
PURE A	DIRECT	THX	ALLST

Speaker Configuration

These settings are set automatically by the Automatic Speaker Setup function (see page 40).

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. The following crossover frequencies can be specified: Full Band, 40 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz, 100 Hz, 120 Hz, 150 Hz, 200 Hz.

Specify Full Band for speakers that can output low-fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speakers’ manuals to determine the optimum crossover frequencies.

If you’re using THX-certified speakers, specify 80 Hz (THX) for all speakers.

1	Press the [RECEIVER] REMOTE
	RECEIVER

MODE button, followed by the [SETUP] button.

The main menu appears onscreen.

4		Use the Up and Down [			]/[	]
		buttons to select “a. Subwoofer,”
	ENTER	and then use the Left and Right
		[	]/[	] buttons to select:
			Yes: Select if a subwoofer is con-
				nected.
			No: Select if no subwoofer is con-
5				nected.
		Use the Up and Down [			]/[	]
		buttons to select “b. Front,” and
	ENTER	then use the Left and Right
		[	]/[	] buttons to select a

crossover frequency.

Note:

•If the Subwoofer setting in step 4 is set to No, this is fixed at Full Band.

6	Use the Up and Down [ ]/[ ]
	buttons to select “c. Center,” and
	then use the Left and Right
	ENTER
	[ ]/[ ] buttons to select a
	crossover frequency.
	If no center speaker is connected, select
	None.

Note:

•If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here.

70