SYSTEM ALIGNMENT

III. PRELIMINARY ALIGNMENT SETUP

The following procedures are intended for complete “Geometry/Convergence” setup. Use the customer’s signal for doing phase, and size adjustments. You can use the internal pat- terns for shape and convergence if the customer signal sources do not have a cross-hatch pattern.

If you are realigning a single CRT, due to replacement, or doing alignment touch up, perform the following steps as needed.

1. Yoke Tilt Alignment

Use a cross-hair or cross-hatch pattern. Monitor only the center- most horizontal line of the pattern to check yoke tilt.

Do not use SW9501, on the 9-1510 module, to disable conver- gence. The vertical circuit is not disabled, only the horizontal is disabled.

a. Set Horizontal DC centering to “0” (red, green, blue). b. Set Vertical DC centering:

Floor: Red = -30; Green = -20; Blue = -30.

Ceiling : Red = 30; Green = 20; Blue = 30.

c. In geometry mode and convergence mode (green, red, and blue) set “SKEW” H = 0 and “SKEW” V = 0.

d. Adjust the Red, Green, and Blue yokes for no horizontal tilt or twist.

If this test shows a need for astimatator alignment perform steps “a” - “l” below.

Astigmatator Alignment Procedure

a. Set the display/sync mode to Forced Mode 6 (HDTV33) and select a cross-hatch or dot pattern.

b. Cut off Red and Blue video or cover the CRT lens assemblies.

c. Set Green electrical focus slightly CCW. This is to make a near display center dot dimly haloed with a bright center. The haloed effect will also be visible with the cross-hatch lines.

d. Use the astigmatator 4-pole magnet to shape the halo and bright spot as round as possible.

e. Use the astigmatator 6-pole magnet, if needed, to help shape the halo and spot round.

f. Use the astigmatator 2-pole magnet (refer to the figure at bottom left of this page) to center the bright spot within the halo. You may also use an intersection, of the cross-hatch, to center the bright area within the haloed area.

g. Use the main yoke magnets to position the signal raster center to the CRT face center. Refer to figure below.

2. Yoke Ring Magnet and Astigmatator Alignment

Verify Only - This is not a normal field adjustment.

The astigmatator assembly should be mounted 62.5 mm from the video output module (from the front edge of the video output module to the six pole rings). Refer to the figure on page 24.

Astigmatator Alignment Verification Test

Adjust for the best electrical and mechanical focus.

Verify spot alignment by rotating Green electrical focus slightly CW to CCW. The Dot shape should not tail or flair. The bright area should remain in the center of the haloed area. Refer to the fig- ure below.

h. Verify spot alignment by rotating Green electrical focus slightly CW to CCW. The Dot shape should not tail or flair. The bright area should remain in the center of the haloed area.

i. Repeat steps “c” thru “h” as needed to obtain the smallest and best round Green center dot with no shape flaring.

j. Adjust for the best electrical and mechanical focus. k. Repeat steps “c” - “j” for the Red and Blue displays. l. Exit forced mode 6 and return to normal video. Set

Brightness and Contrast to 50.

Note: The yoke adjustments should not be touched during the remaining setup steps.

3. Ceiling/Front Projection Lens Angle Focus Alignment

If this PRO900X system is equipped with the “lens assembly focus” spring, the following procedure must be completed. This procedure must be completed as part of the system mechanical

P A G E 2 2

3276-A

 

Page 21 Page 23
Page 22
Image 22
OPPO Digital Model PRO900X setup guide Yoke Tilt Alignment, Astigmatator Alignment Procedure
Page 21 Page 23

Model PRO900X specifications

OPPO Digital has made a name for itself in the world of high-fidelity audio equipment, and the new PRO900X model exemplifies their commitment to quality and innovation. Aimed at audiophiles and casual listeners alike, the PRO900X stands out for its exceptional sound performance, versatile connectivity options, and sleek design.

One of the primary features of the OPPO PRO900X is its advanced digital-to-analog converter (DAC). This device utilizes state-of-the-art technology to ensure that audio reproduction is as true to the original recording as possible. The PRO900X is equipped with a high-performance DAC that supports multiple audio formats, including PCM and DSD, allowing users to experience their favorite tracks in pristine quality.

Additionally, the PRO900X boasts a powerful amplifier unit that drives a wide range of headphones and speakers effortlessly. This ensures that users can enjoy rich, dynamic sound filled with detail and clarity, regardless of the audio source. The amplifier is designed to deliver high output impedance, which enhances the listening experience, especially when paired with high-impedance headphones.

Connectivity is another strong suit of the OPPO PRO900X. Featuring USB, optical, coaxial, and Bluetooth connections, this model caters to different user needs. It supports high-resolution audio streaming via Bluetooth, enabling users to wirelessly connect their smartphones or tablets without sacrificing sound quality. The PRO900X is compatible with a variety of devices, making it an ideal choice for both home and portable audio setups.

The design of the PRO900X reflects OPPO's aesthetic philosophy, combining elegant looks with functional ergonomics. The unit features a minimalist front panel with easily accessible controls, allowing users to navigate through different settings and inputs effortlessly. The robust build quality ensures longevity, making it a reliable addition to any audio setup.

Finally, the OPPO PRO900X comes with user-friendly software that facilitates firmware updates and customizable audio settings. This ensures that the device remains compatible with future technologies while allowing users to tailor their listening experience to their preferences. With its impressive features, advanced technologies, and sleek design, the OPPO Digital Model PRO900X is poised to be a game-changer in the high-end audio market.
Top Page Image Contents