Assembly Operating Instructions | Oreck XL2700HH, XL2610HH, XL2700RH

E N G L I S H

Assembly

Operating Instructions

To assist you in identifying components of your vacuum, the parts have been numbered as follows:

1Handle section, upper

2Tube, lower

3Power head

4Outer bag

5Paper filter dust bag

6 Power cord

7Retaining spring

8Bag tension bar

9Zip fastener

10On/off switch

11Cord hook

12Plastic loop/cable clamp

13Connector assembly

14Fan housing

15Cord assembly

	10
9	11
9	1
	12

		2	6
			6
8	7	14	15
	7	14

3

To Operate

Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag.

Plug the power cord into an electrical outlet and press the On(l) - OFF(O) switch on handle assembly when ready to operate.

General Information

The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference.

Operating Recommendations

This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its operation:

1	Before assembling appliance,
	remove two screws from the
	connector assembly. Remove
	cardboard insert by pulling
	upward.

1.	When inserting a new disposable paper filter dust bag—
	FIRST PUFF OUT and OPEN THE BAG.
2.	When the disposable filter dust bag is full, REPLACE IT.
3.	If at any time the machine does not pick up properly or
	makes an unusual noise, STOP OPERATION and service.
4.	Although your upright will pick up pins, paper clips, and
	other small objects, it is recommended that these be
	removed from the floor before you vacuum. Failure to do
	so may result in permanent damage to the motor suction
	fan and its housing.
5.	WARNING: Do not use your vacuum cleaner on damp
	or wet surfaces. This will cause damage to the vacuum

2	Upper
	Handle
	Connector
	Assembly
3

With ON/OFF switch facing the front of the unit, slide upper handle section over matching section of the connector assembly. Insert short screw into top hole and long screw into the bottom hole then tighten firmly until handle is no longer loose.

Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip.

	cleaner and is dangerous to the user. Damage caused by
	use on wet or damp surfaces is not covered under
	warranty.
6.	REPLACE THE BELT EVERY 6 MONTHS.
7.	Change the disposable filter dust bag at least once a
	month—even if it is not full! The collected dust in the dust
	bag can cause odor, attract moisture, act as a breeding
	area and can affect the efficie cy f the cleaner.
8.	DO NOT run the vacuum cleaner over cord. The
	revolving brush could damage the cord.

Disposable Paper Filter Dust Bags

Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the paper bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the paper bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power. Increase the CLEANING POWER of your cleaner by changing the bag often.

To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.

Be sure the disposable paper filter dust bag is installed properly.

XL2700RH, XL2610HH, XL2700HH, XL2600HH specifications

The Oreck XL series of vacuum cleaners, including models XL2600HH, XL2700HH, XL2610HH, and XL2700RH, represents a pinnacle in lightweight cleaning technology. Designed for both efficiency and user comfort, these models cater to a variety of floor types and cleaning needs, making them ideal for residential and commercial spaces alike.

One of the standout features of the Oreck XL series is their lightweight design. Weighing around 8 pounds, these vacuums are easy to maneuver, reducing fatigue during extended cleaning sessions. Their slim profile ensures they can easily reach under furniture and into tight corners, maximizing cleaning potential.

The XL2600HH and XL2700HH models are equipped with Oreck's proprietary, high-speed roller brush technology. This feature allows for effective deep cleaning while lifting dirt, dust, and allergens from carpets and bare floors. The brushes rotate at a high velocity, enabling the machines to dig deep into carpet fibers and extract particles that other vacuums may leave behind.

Another important aspect of these models is their multi-floor capability. Whether you're cleaning carpet, tile, hardwood, or laminate, the XL series provides versatile cleaning solutions. The adjustable floor settings seamlessly adapt to different surfaces, allowing users to switch from one type of flooring to another without losing suction power.

The Oreck XL2610HH and XL2700RH models highlight advanced air filtration systems, including a HEPA filtration option that effectively captures 99.97% of particles as small as 0.3 microns. This feature is particularly beneficial for allergy sufferers, as it helps maintain a cleaner indoor air environment.

Additionally, the XL series boasts a unique top-fill design, allowing the bags to fill completely without losing suction. This design maximizes efficiency by utilizing all the available space within the bag.

Furthermore, the Oreck Vacuums come with a warranty, demonstrating the manufacturer's confidence in their durability and performance. With their combination of lightweight design, advanced features, and effective cleaning capabilities, the Oreck XL2600HH, XL2700HH, XL2610HH, and XL2700RH vacuum cleaners stand out as reliable choices for maintaining cleanliness in any space.

Oreck XL2700HH, XL2610HH, XL2700RH, XL2600HH warranty Assembly Operating Instructions

Models: XL2700RH XL2610HH XL2700HH XL2600HH