Outlaw Audio Model 1070 Remote Control, These buttons control the Model 1070’s volume

Owner’s Manual

Model 1070 Remote Control

RC				PWR
1
RC	CBL	AUX	VCR	TV
2
	SAT	CD	AMP	TNR
RC	1		2	3
3	4		5	6
	7		8	9
RC				ENTER
			0
4	MUTE			SYNC
			LAST
			NIGHT
RC	VOL		SLEEP	CH
5
RC			TONE
6
RC	GUIDE			EXIT
	TEST			TRIM
7
RC
8			SET
RC
9
RC	INFO			MENU
10	7.1			OSD
RC	PRESET DOWN		DIRECT	PRESET UP
11
RC	TUNE MODE	AM / FM		MEMORY
12
	VIDEO 1	VIDEO 2	VIDEO 3	VIDEO 4
RC
13	CD	AUX	TAPE	DVD

DOLBY MODES DTS MODES STEREO MODES BYPASS

RC

14

RC

15

RC

16

RC

17

RC

18

RC

19

RC

20

RC

21

RC

22

RC

23

RC

24

RC

25

RC

26

RC

27

RC

28

Remote Control

The Model 1070’s hand held remote controller is a pre-programmed universal unit that contains an extensive library of IR codes and can control up to seven other system components in addition to duplicating every one of the Model 1070’s front panel functions. All of these choices are shown on the Model 1070’s front panel and on-screen displays.

Activate the remote’s backlight by simply touching any pushbutton. This lets you use the remote comfortably even in a dark room. The backlight stays on for 5 seconds after you’ve touched a pushbutton.

RC1 Setup button (see pages 42-43)

Holding down this button for three seconds causes the remote to enter setup mode. In this mode, you can enter an entire set of codes for another device to be controlled.

RC2 Device Control Selector buttons (see pages 26, 37, 42-44)

Selects the component you want to control with the remote. Push TNR

to control the Model 1070.

RC3 Numeric keypad (see pages 40-44)

Buttons for control functions requiring you to enter numbers, such as command code selection when programming the remote, using the tuner, selecting CD and DVD player tracks, etc.

RC4 Mute button (see page 38)

Mutes the Model 1070’s output. Pushing the button again restores the volume to its previous level. Changing the front panel or remote control volume setting also releases the mute function. Mute status is shown on the front panel display.

RC5 Volume Up/Down buttons (see pages 38, 42-44)

These buttons control the Model 1070’s volume.

RC6 Sleep button (see page 39)

Activates the sleep timer, putting the receiver into Standby mode after a certain period. The first push sets the timer at 90 minutes; subsequent pushes scroll though 75, 60, 45, 30, 20, 10, 5 minutes, and Off. Once the timer is set, pushing this button again displays the remaining time on both the front panel and the on-screen display.

RC7 Guide/Test dual function button (see page 39)

Model 1070: Test turns on the test tone generator to set speaker levels. To route the test tone from one speaker to the next, press the Left or Right Cursor buttons. Use the Up/Down cursor buttons to adjust levels. Press Set when finished.

Other components: Guide calls up the program guide on satellite receiv- ers and cable boxes.

RC8 Cursor control buttons (menu navigation)

In general, the Up and Down cursor buttons select a particular function or parameter from the on-screen menu while the Left and Right cursor buttons adjust whatever function or parameter that’s been selected. Set activates selections made while using the on-screen menu.

RC9 Direct/ dual function button (see page 40)

Model 1070: Direct enables access to a radio station directly. Press once, then enter the station’s frequency using the numeric keys.

Other components: begins the play function.

10

Outlaw Audio