Channel Trim

Channel Trim allows you to fine-tune the channel levels to compensate for various soundtrack anomalies. For example, you may play a movie and find that the center (dialogue) channel sounds weak, making the movie hard to follow. Simply trimming the center channel up a decibel or two can fix the problem. Or another movie may have much more bass than normal; trimming the subwoofer channel down a few decibels should balance the sound correctly.

You can trim the channels while you are listening to a source, or you can trim the channels using the Model 1070’s internal test tone. The trim range is +10dB to -10dB.

To adjust channel level while listening to a source:

1.Press TRIM on the remote control.

“TRIM LEVEL ADJUST” will appear in the front panel display and in the on-screen messages (unless you selected OSD: OFF in the Input Con- figuration menu). FRONT LEFT” will be the first channel to be shown on-screen and on the front-panel display along with the current channel output level offset.

2.Press the or buttons to adjust the level as desired.

3.When the desired level offset is set, use the and buttons to move through the list of channels.

Repeat steps 2 and 3 until you finished adjusting the channel levels.

4.Press SET when you are finished adjusting the channel outputs or wait a few seconds for the display to disappear.

To adjust channel level using the test tone, use the same procedure described above, except start the process by pressing the TEST button on the remote instead of the TRIM button. :

Recording a Source

You can record from any input source connected to the Model 1070 when you have an audio or video recorder properly connected to the appropriate output jacks on the rear panel but you cannot monitor the output of the recorder through the Model 1070 while recording.

To record from a currently selected analog input source:

1.Prepare your analog recording device.

Follow the recommended procedure from the recorder manufacturer about settings, etc.

2.Set the device to the record mode and begin recording.

The source audio signals appear at the Tape Record Outputs and the Video 1 audio outputs. If the source contains a video signal, it appears at both the composite and S-Video Record Outputs.

To record from a currently selected digital input source:

1.Prepare your digital recording device.

Follow the recommended procedure from the recorder manufacturer about settings, etc.

2.Set the device to the record mode and begin recording.

The source audio signals appear at the Coaxial and Optical Digital Audio Output jacks. If the source contains a video signal, it appears at both the composite and S-Video Record Outputs.

Owner’s Manual

Model 1070 Operation

Notes on recording: You can record analog to analog and digi- tal to digital but you cannot record analog to digital or digital to analog through the Model 1070.

If you change the input source during recording, you will record the signals from the newly selected input source from that point on.

Night Mode Selection

The Model 1070’s Night Mode is intended for late-night listening. It suppresses the loud peaks in movie soundtracks and music videos so that the sound from your system does not disturb others. Yet you will still be able to play the system loud enough so you can hear dialogue clearly. Night Mode works only with Dolby Digital soundtracks.

You can activate Night Mode through the Surround Configuration sub-menu (see page 32) or directly from the remote control.

To adjust Night Mode from the remote control when a Dolby Digital source is playing:

1.Press the NIGHT button on the remote control.

The current setting of Night Mode appears on the front panel display and in the on-screen messages (unless you selected OSD: OFF in the Input Configuration menu.)

2.Press the NIGHT button to toggle between the two modes.

No Comp means no compression (i.e., Night Mode Off)

DR Comp means dynamic range compression (i.e., Night Mode On)

3.Press EXIT on the remote control to exit Night Mode selection, or wait a few seconds for the display to disappear.

Sleep Timer

The Model 1070’s sleep timer automatically shuts the unit off after a predeter- mined amount of time. The sleep time can be activated through the System Configuration sub-menu (see page 37), or directly from the remote control.

To activate the sleep timer from the remote:

1.Press SLEEP on the remote.

“SLEEP TIME: 90 MIN” appears on the lower line of the front-panel

display and in the on-screen messages (unless you selected OSD: OFF in the Input Configuration menu.)

2.Press SLEEP repeatedly to reduce the amount of time before the Model 1070 shuts off.

The available choices are:

90MIN75MIN60MIN45MIN30MIN20MIN10MIN5MINOFF

Choosing one of the time settings will cause the Model 1070 to turn itself off after selected amount of time.

Choose OFF to disengage the sleep timer function

3.Press EXIT on the remote to remove the sleep timer display, or wait a few seconds for the display to disappear.

4.To check the amount of time left on the sleep timer, press SLEEP again.

Model 1070 7.1 Channel Surround Sound Receiver

39

Page 38 Page 40
Page 39
Image 39
Outlaw Audio 1070 owner manual Channel Trim, Recording a Source, Night Mode Selection, Sleep Timer
Page 38 Page 40

1070 specifications

Outlaw Audio has made a name for itself in the high-performance audio market, and their Model 1070 receiver is a prime example of their commitment to delivering exceptional sound quality. The Outlaw Audio 1070 is a versatile surround sound receiver that combines advanced technology with user-friendly features, designed to elevate your home theater experience.

One of the standout features of the 1070 is its powerful amplification system. It delivers 7 channels of amplification, each capable of producing 60 watts per channel into 8 ohms. This robust power output ensures that even the most demanding audio tracks are handled with ease, providing clarity and depth across the frequency spectrum. The receiver is also equipped with an array of connection options, including HDMI inputs, to accommodate all of your audio and video sources seamlessly.

The 1070 employs advanced digital processing technologies that enhance your listening experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing you to enjoy multidimensional audio for movies, music, and gaming. Outlaw Audio has integrated their proprietary Outlaw Bass Management system, which offers customizable bass settings to suit your room’s acoustics and your personal preferences. This feature ensures that your subwoofer delivers a seamless integration with your main speakers, enhancing the overall impact of your audio.

For those who appreciate fine-tuning their listening experience, the Outlaw 1070 includes an easy-to-use graphical user interface that simplifies setup and adjustment. The on-screen menus provide straightforward access to configuration settings, making it simple to calibrate your system for optimal performance.

Another key characteristic of the Outlaw 1070 is its build quality. The receiver is housed in a sturdy chassis, designed to minimize interference and reduce vibrations, a consideration that makes a difference in sound quality. The high-quality components and construction reflect Outlaw Audio’s dedication to crafting products that meet the expectations of audiophiles.

In conclusion, the Outlaw Audio 1070 offers a remarkable combination of power, flexibility, and advanced technologies that cater to both casual listeners and serious audiophiles alike. With its impressive amp capabilities, robust surround sound processing, and user-friendly design, the 1070 stands as a compelling choice for anyone looking to enhance their home audio system. Whether you’re enjoying a movie night or listening to your favorite music, the Outlaw Audio 1070 is engineered to deliver an immersive sound experience.
Top Page Image Contents