Follow the instructions provided by Vonage | Over And Back PAP2

Phone Adapter with 2 Ports for Voice-over-IP

1.Using a telephone cable, connect your telephone to the PHONE 1 port of the Phone Adapter.

2.If you have a second Vonage line on your account, then connect another telephone or a fax machine to the PHONE 2 port of the Phone Adapter.

3.Connect the included Ethernet network cable to the ETHERNET port of the Phone Adapter. Connect the other end to the one of the Ethernet ports on your router or gateway.

4.Connect the included power adapter to the POWER port on the back panel of the Phone Adapter. Connect the other end to a standard electrical outlet.

5.The Power, Ethernet, and Phone LEDs will be solidly lit when the Phone Adapter is ready for use.

6.Follow the instructions provided by Vonage.

If you need to manually configure the Phone Adapter’s network settings, you can use the telephone; for instructions, proceed to “Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu.”

The installation of the Phone Adapter is complete. Now you can pick up your phone and make calls.

NOTE: Vonage supports 7-, 10-, and 11-digit dialing. Use 7-, 10-, or 11-digit dialing for calls within the same area code as your Vonage phone number. Use 10- or 11-digit dialing for calls outside of your area code.

Figure 3-2: Connect the Telephone Cable

Figure 3-3: Connect the Ethernet

Network Cable

Figure 3-4: Connect the Power

Proceed to the next section, “Placement Options,” if you want to attach the Phone Adapter’s base.

6	Chapter 3:	Connecting the Phone Adapter
	Instructions for	Connecting the Phone Adapter

Image 12

Over And Back PAP2 manual Follow the instructions provided by Vonage, Connect the Telephone Cable

Contents

Phone Adapter Page How to Use this Guide Copyright and Trademarks Phone Adapter with 2 Ports for Voice-over-IP Table of Contents Back Panel Front Panel Introduction WelcomeWhat’s in this Guide? Introduction Getting to Know the Phone Adapter Back Panel Ports Front Panel Phone Adapter’s LEDs are located on the front panelIncoming call has been detected An incoming call has been detected Connecting the Phone Adapter Instructions for Connecting the Phone AdapterOverview Internet Follow the instructions provided by Vonage Connect the Telephone Cable Placement Options Stand OptionRemove the plate from the Phone Adapter’s bottom panel Phone Adapter’s Interactive Voice Response Menu Wall-Mount Option Measurement between Wall-Mount Slots Using the Phone Adapter’s Interactive Voice Response Menu Accessing the Interactive Voice Response MenuUsing the Interactive Voice Response Menu Use this command to enter Response Menu Interactive Voice Response MenuNot press any other keys until you Key or hang up to exit Has been enabled or disabled. If 101 Enter 1 to enableEnter 0 to disable Check Dhcp 100 Address using Static IP address When entering a Decimal pointSubnet Mask Mask using Network mask When entering a Decimal point Address Address using Static gateway IP address When entering a Decimal pointPhone Adapter Manual Reboot 732668 131 Enter the IP Configuring the Settings for Your Internet Phone Service Appendix a Troubleshooting Common Problems and Solutions Appendix a Troubleshooting Application Start and End Protocol IP Address Enable Internet phone 5060 toIP address Phone Adapter Internet phone 53 to IP address Phone Adapter Internet phone 69 to Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Frequently Asked Questions Ethernet LED does not light up Can I make calls while I’m browsing the Internet? Appendix B Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Dimensions 98 x 3.98 x H x D Storage Humidity ~90% Non-CondensingMm x 101 mm x 15 mm Appendix E Warranty Information Limited Warranty Appendix E Warranty Information Appendix F Regulatory Information FCC Statement Appendix F Regulatory Information Vonage LinksysToll-free from US