Packard Bell M5850 guide

2.2Disconnect the cable housing then you can remove front bezel.

2.3Remove the screw

2.4Pulling out the HDD cage

33

Image 39

Packard Bell M5850 manual

Contents

Ixtreme M5850 Service Guide Revision History Date Chapter Updated Copyright Conventions Preface Standard Cmos Features Block DiagramHardware Specifications and Configurations Setup Utility Menus Introduction Introducing the Motherboard Features Integrated I/O Bios Firmware Label Component Mainboard Components Block Diagram Icon Component Description Ixtreme M5850 Rear view Audio Jack Function Table Color/Use Headphone1CH Component Description Port Introduction Speakers System PeripheralsMouse PS/2 or USB, manufacturing option Keyboard PS/2 or USB, manufacturing option Card Reader Option Main Board Major Chips Hardware Specifications and ConfigurationsBios Hotkey List Specification Audio Interface System MemoryCache Memory Video Interface Devices Idle Shut Down Power ManagementIDE Interface USB Port Suspend Mode Power Management Function Acpi support functionDevice Standby Mode Global Standby Mode Entering the Setup Utility Using BiosAbout the Setup Utility Standard Configuration Bios Setup UtilityMain Bios Navigation KeysDate and Time Using Bios Updating the Bios Bios Setup UtilityAdvanced Clock to All DIMM/PCIE DisabledMiscellaneous Advanced Chipset Configuration Spread Spectrum EnabledBootup Num-lock On USB Beep Message Disabled Legacy USB Support Enabled Onboard Sata Controller EnabledOnboard Sata Mode Ahci Onboard USB Controller Enabled Onboard LAN Option ROM Disabled Onboard Graphics Controller EnabledOnboard Audio Controller Enabled Onboard LAN Controller Enabled Smart Fan Enabled System Component Characteristics Bios Setup UtilityPower Change Supervisor Password Press Enter Bios Setup UtilitySecuritySupervisor Password Not Installed User Password EFI Device Priority Press Enter Bios Setup UtilityBoot options1st Boot Device/2nd Boot Device/3rd Boot Device Set Priority Order Optical Disk Drive Priority Press Enter Hard Disk Drive Priority Press Enter Network Device Priority Press Enter Fast Boot DisabledQuiet Boot Enabled Removable Device Priority Press Enter Bios Setup UtilityExit Machine Disassembly and Replacement Before You Begin General Information Standard Assembly Process Opening the chassisRemoving front bezel and HDD Cage Page Install the PSU Setting the Motherboard Page DIMM4 DIMM2 DIMM3 DIMM1 Assembly motherboard Insert the ODD/HDD SKU without HDD Carrier ODD Remove the HDD Carrier Install the HDD devices HDD Carrier Installed on SATA3 Master HDD Installed on SATA0 Insert Add-on card Close the Front BezelPage Page Connect Pata power cable Fix the screw Close the bracket Install system fan Overview Standard Disassembly Process Opening the computerRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages List Specifics about the type and location of the memory error Hard Disk Drive Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Main board and Memory Audio Error Symptom Action/FRU CD/DVD-ROM Drive Keyboard Error Symptom Action/FRU Video and MonitorPower Supply Parallel/Serial Ports Other Problems Error Symptom Action/FRU Undetermined Problems Choosing a Computer Case Jumper and Connector InformationSafety Precautions Installing the Motherboard in a Case Setting Jumpers Checking Jumper Settings Checking Jumper Settings Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case Components Sysfan Cooling Fan Power Connector Pin Signal Name Function Pin Signal NameATX12V ATX 12V Power Connector Pin Signal Name Power Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Reset Switch Installing Hardware Installing the ProcessorBefore installing the Processor Following illustration shows CPU installation components CPU Installation Procedure Installing Memory Modules Installation ProcedureMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard Drives Installing Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional Devices Sata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOptionFUSB1~4 Front Panel USB headers ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded Diagram RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM Oddbuttontop Oddbuttonbottom Page FRU List