Removing the power-supply | Packard Bell M5850 manual

7.8Release the CPU Cooler screw x4 then remove it

7.9Remove the CPU

8.Removing the power-supply

8.1 Disconnect the three screws fixed in the rear chassis

59

Image 65

Packard Bell M5850 manual Removing the power-supply

Contents

Ixtreme M5850 Service Guide Revision History Date Chapter Updated Copyright Conventions Preface Hardware Specifications and Configurations Block DiagramSetup Utility Menus Standard Cmos Features Introduction Introducing the Motherboard Features Integrated I/O Bios Firmware Label Component Mainboard Components Block Diagram Icon Component Description Ixtreme M5850 Rear view 1CH Audio Jack Function TableColor/Use Headphone Component Description Port Introduction Mouse PS/2 or USB, manufacturing option System PeripheralsKeyboard PS/2 or USB, manufacturing option Speakers Card Reader Option Bios Hotkey List Hardware Specifications and ConfigurationsSpecification Main Board Major Chips Cache Memory System MemoryVideo Interface Audio Interface IDE Interface Power ManagementUSB Port Devices Idle Shut Down Device Standby Mode Power Management Function Acpi support functionGlobal Standby Mode Suspend Mode About the Setup Utility Using BiosStandard Configuration Entering the Setup Utility Date and Time Bios Setup UtilityMainBios Navigation Keys Using Bios Updating the Bios Miscellaneous Bios Setup UtilityAdvancedClock to All DIMM/PCIE Disabled Bootup Num-lock On Spread Spectrum EnabledUSB Beep Message Disabled Advanced Chipset Configuration Onboard Sata Mode Ahci Onboard Sata Controller EnabledOnboard USB Controller Enabled Legacy USB Support Enabled Onboard Audio Controller Enabled Onboard Graphics Controller EnabledOnboard LAN Controller Enabled Onboard LAN Option ROM Disabled Smart Fan Enabled System Component Characteristics Bios Setup UtilityPower Supervisor Password Not Installed Bios Setup UtilitySecurityUser Password Change Supervisor Password Press Enter 1st Boot Device/2nd Boot Device/3rd Boot Device Bios Setup UtilityBoot optionsSet Priority Order EFI Device Priority Press Enter Optical Disk Drive Priority Press Enter Hard Disk Drive Priority Press Enter Quiet Boot Enabled Fast Boot DisabledRemovable Device Priority Press Enter Network Device Priority Press Enter Bios Setup UtilityExit Machine Disassembly and Replacement Before You Begin General Information Removing front bezel and HDD Cage Standard Assembly ProcessOpening the chassis Page Install the PSU Setting the Motherboard Page DIMM4 DIMM2 DIMM3 DIMM1 Assembly motherboard Insert the ODD/HDD SKU without HDD Carrier ODD Remove the HDD Carrier Install the HDD devices HDD Carrier Installed on SATA3 Master HDD Installed on SATA0 Insert Add-on card Close the Front BezelPage Page Connect Pata power cable Fix the screw Close the bracket Install system fan Overview Removing the Front Bezel Standard Disassembly ProcessOpening the computer Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages List Specifics about the type and location of the memory error Error Symptom Action/FRU Processor / Processor Fan Error Symptoms ListMain board and Memory Hard Disk Drive Audio Error Symptom Action/FRU CD/DVD-ROM Drive Power Supply Error Symptom Action/FRU Video and MonitorParallel/Serial Ports Keyboard Other Problems Error Symptom Action/FRU Undetermined Problems Safety Precautions Jumper and Connector InformationInstalling the Motherboard in a Case Choosing a Computer Case Setting Jumpers Checking Jumper Settings Jumper Type Description Setting Default IIIustration Checking Jumper SettingsJumper Settings Connecting 24-pin power cable Connecting Case Components ATX12V ATX 12V Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPin Signal Name Power/Sleep/Message waiting LED Pin Signal Name FunctionReset Switch Power Switch Before installing the Processor Installing HardwareInstalling the Processor Following illustration shows CPU installation components CPU Installation Procedure Memory Memory Bus Installing Memory ModulesInstallation Procedure Sata cable optional Sata power cable optional Installing Serial ATA Hard Drives Installing Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional Devices FUSB1~4 Front Panel USB headers Sata 1~6 Serial ATA connectorsSPDIFOUT1 Spdif out headerOption ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded Diagram RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM Oddbuttontop Oddbuttonbottom Page FRU List