Panasonic AG-DVX100P manual Scene File screen

Setting menus

SCENE FILE screen

Item/		Description of settings
(display mode)
DETAIL LEVEL	For adjusting the detail amount.
(Camera)	–7--- 0 --- +7
CHROMA LEVEL	For adjusting the chroma level.
(Camera)	–7--- 0 --- +7
CHROMA	For finely adjusting the chroma phase.
PHASE	–7--- 0 --- +7
(Camera)
COLOR TEMP	For finely adjusting the color temperature
(Camera)	(for performing fine adjustments after the
	white balance has been adjusted).
	–7--- 0 --- +7
MASTER PED	For adjusting the black master pedestal
(Camera)	which serves as the video reference.
	–15 ---0 ---+15
A. IRIS LEVEL	For setting the auto iris target value.
(Camera)	–4--- 0 --- +4
GAMMA	For selecting the gamma curve.
(Camera)	CINE-LIKE:
	The gamma curve which gives the
	images a cinema-like finish is used.
	In order to make full use of the CINE-
	LIKE gamma characteristics, it is
	recommended that the lens iris be set
	lower (by approx. 1/2) than the regular
	video level.
	LOW:
	Using a gamma curve with a moderate
	gradient for the low-luminance areas, the
	images are given a calm, composed look.
	A sharp touch is conveyed by the
	contrast.
	NORM:
	Standard images are produced.
	HIGH:
	Using a gamma curve with a sharp
	gradient for the low-luminance areas, the
	gradations of the dark areas are
	extended to make them appear brighter.
	A soft touch is conveyed by the contrast.
SKIN TONE DTL	For switching the skin tone detail ON or
(Camera)	OFF.
	When ON is selected, the detail in the skin
	tone areas is diminished and the graininess
	of the skin is reduced.
	OFF	ON
MATRIX	For selecting the matrix table and
(Camera)	expressing the colors during shooting.
	NORM:
	Colors suited to shooting outdoors or
	under light sources using halogen lamps
	are expressed.
	FLOU:
	Colors suited to shooting indoors under
	fluorescent light sources are expressed.
	CINE-LIKE:
	Colors suited to cinema-like shooting are
	expressed.

Item/	Description of settings
(display mode)
V DETAIL FREQ	For setting the detail in the vertical direction
(Camera)	when shooting in the progressive mode.
	THIN : The detail is made finer.
	THICK : The detail is made coarser.
	O When “THIN” has been selected as the
	item’s setting and the images shot in the
	progressive mode are played back using
	a standard TV monitor (60i: interlace),
	some flickering will occur on the
	horizontal lines and on the diagonal lines
	near the horizontal.
	When playing back a tape in a
	progressive environment, this flickering
	is reduced by selecting “THIN” as the
	item’s setting, which will also enable
	images with a higher resolution than that
	with the “THICK” setting to be obtained.
PROGRESSIVE	For setting shooting in the progressive
(Camera)	mode.
	OFF:
	Shooting is not performed in the
	progressive mode.
	30P:
	Shooting is performed in the 30P mode
	(30 frames/sec.).
	24P:
	Shooting is performed in the 24P mode
	(24 frames/sec.).
	Images are recorded on the tape using
	the [2:3] conversion system.
	24P(ADV):
	Shooting is performed in the 24P
	advanced mode (24 frames/sec.).
	Images are recorded on the tape using
	the advanced conversion system.
NAME EDIT	For editing the name of the scene file
(Camera)	selected by the scene file dial.
SAVE/INIT	SAVE:
(Camera)	For saving the scene file settings after
	changes have been made to them.
	O If the menu mode is released without
	saving the changes, the original scene
	file settings will be restored when
	operation is switched to the VCR mode
	or the power is turned off.
	INITIAL:
	For returning the scene file settings
	selected by the scene file dial to the factory
	settings.

39