Panasonic AG-DVX100P manual Recording Setup screen

Setting menus

RECORDING SETUP screen

Item/		Description of settings
(display mode)
REC SPEED	For selecting the recording time mode.
(Camera)	SP : SP (standard play) mode
(VCR)	LP : LP (long play) mode
AUDIO REC	For selecting the system for converting the
(Camera)	recording to PCM audio.
(VCR)	12 bit : 12-bit/32kHz
	16 bit : 16-bit/48kHz
MIC ALC	For setting the mic level automatic control
(Camera)	function to ON or OFF.
	OFF	ON
	Audio distortion caused by excessively high
	input level can be minimized by selecting
	ON for this item.
	O The recording level of the audio signals
	must be adjusted using the AUDIO
	controls, irrespective of this setting.
MIC GAIN 1	For setting the input level of the external
(Camera)	microphone which is connected to the
	INPUT 1 connector.
	-50 dB	-60 dB
MIC GAIN 2	For setting the input level of the external
(Camera)	microphone which is connected to the
	INPUT 2 connector.
	-50 dB	-60 dB
1394 TC REGEN	For selecting the time code to be recorded
(VCR)	when recording the signals of a component
	connected to the DV connector.
	OFF:
	The signals are recorded using the time
	code which was set using the TC MODE
	item, TCG item and FIRST REC TC
	item.
	ON:
	The signals are recorded using the time
	code of the signals which have been
	input to the DV connector.
	O When ON has been selected as this
	item’s setting, this setting takes
	precedence over the TC MODE item,
	TCG item and FIRST REC TC item
	settings.
	O When no signals are supplied to the DV
	connector, the TC MODE item, TCG item
	and FIRST REC TC item settings are
	followed.
TC MODE	For selecting the time code correction
(Camera)	mode in which the time code of the internal
(VCR)	time code generator is to be recorded.
	DF :	The drop frame mode is used.
	NDF : The non-drop frame mode is used.
	O When the progressive mode has been
	set to 24P or 24P (ADV), the non-drop
	frame mode is established regardless of
	this item’s setting.

The underlining indicates the factory setting.

Item/	Description of settings
(display mode)
TCG	For setting the operation mode in which the
(Camera)	internal time code generator is to be run.
(VCR)	FREE RUN:
	The internal time code generator is run
	regardless of the operation mode.
	REC RUN:
	The internal time code generator is run
	during recording.
FIRST REC TC	For selecting the time code which is to be
(Camera)	recorded when recording is started.
(VCR)	REGEN:
	Recording proceeds in such a way that
	the time code continues on (is
	regenerated) from the time code on the
	tape.
	PRESET:
	The time code is not regenerated from
	the time code on the tape.
	The time code is recorded using the
	value set in the TC PRESET item
	serving as the initial value.
	However, the time code is forcibly
	regenerated when shooting with frame-
	to-frame continuity has been performed.
TC PRESET	For setting the initial value of the time code
(Camera)	to be recorded.
(VCR)	This item’s setting is valid when PRESET
	has been selected as the setting for the
	FIRST REC TC item.
	O When the progressive mode has been
	set to 24P or 24P (ADV), set the frame
	value to 0 or to a multiple of 5. If any
	other value is set, the time code
	recorded will shift.
1394 UB REGEN	For selecting the user’s bit to be recorded
(VCR)	when recording the signals of the
	component connected to the DV connector.
	OFF:
	The user’s bit selected for the UB MODE
	item is used for the recording.
	ON:
	The user’s bit of the signals input to the
	DV connector is used for the recording.
	O When ON has been selected as this
	item’s setting, this setting takes
	precedence over the UB MODE item
	setting.
	O The user’s bit is not recorded if the
	signals do not contain the user’s bit
	information.
	O When no signals are supplied to the DV
	connector, the UB MODE item setting is
	followed.

43