Setup menus (continued)

USER menu <OPERATION>

No./Item

Description

 

 

114

This selects whether to cause the

 

REC INH lamp to flash or light up

REC INH

when the cassette has been set to the

LAMP

accidental erasure prevention status.

0000 LIGHT : The lamp lights up.

0001 FLASH : The lamp flashes.

Note:

When the REC INHIBIT switch is set to ON, the REC INH lamp always lights regardless of the general setting status.

115This selects whether to enable or disable the operation of the EJECT

EJECT SW

button on the front panel.

INH

0000

REC :

 

 

Operation is disabled while the unit

 

is in the recording mode.

 

0001

OFF :

 

Operation is enabled in all modes.

120This selects the modes for the picture and sound output when the

EJECT EE SEL

tape is ejected.

 

0000

EE : EE mode

 

0001 BLACK :

 

The picture turns black, and the

 

sound is muted.

 

0002

GRAY :

 

The picture turns gray, and the

 

sound is muted.

 

Note:

 

 

The IEEE 1394 digital output video will

 

be black even if GRAY is selected.

 

 

121

This selects whether the EE mode or

 

playback mode is to be established

F/R EE SEL

during fast forwarding or rewinding.

 

0000

EE : EE mode

 

0001

TAPE : Playback mode

122This select whether the EE mode or playback mode is to be established

STOP EE SEL when operation is stopped.

0000 EE : EE mode

0001 TAPE : Playback mode

Note:

The selection is complied with even in the standby OFF mode. However, the picture will turn gray (black for IEEE 1394 digital output) when TAPE is selected.

No./Item

 

Description

 

 

160

This sets the repeat play mode.

MEMORY

0000

OFF :

MODE

No repeat play (normal operation)

0001 M-STOP :

 

 

The tape stops near the BEGIN point when a

 

FF or REW operation has been performed.

 

0002

REPT1 :

 

During playback, the tape is rewound to the

 

BEGIN point and stopped when the END

 

point is reached.

 

0003

CONT :

 

During playback, the tape is rewound to the

 

BEGIN point and then played, and these

 

steps are repeated when the END point is

 

reached.

161This sets the BEGIN point in the repeat play mode.

CTL BGN

Whether TC or CTL is displayed on the counter

or

TC BGN

when the COUNTER button is pressed is set

here. When there is no setting, --:--:--:-- appears,

 

 

and the tape start serves as the BEGIN point.

162This sets the END point in the repeat play mode.

END

Whether TC or CTL is displayed on the counter when the COUNTER button is pressed is set here. When there is no setting, --:--:--:-- appears, and the tape end serves as the END point.

163This sets the output image when the tape returns to the BEGIN point in

REPT MODE

the repeat play mode.

 

0000 FREEZE :

 

The tape returns to the BEGIN point

 

while the playback image at the

 

END point remains frozen.

 

0001 BLACK :

 

The tape returns to the BEGIN point while

 

a BLACK picture remains on the screen.

 

0002 EE_SEL :

 

The tape returns to the BEGIN point

 

with an image which is in

 

compliance with the setup menu

 

item No.121 (F/R EE SEL) setting.

 

Note:

 

If, when FREEZE has been selected, the

 

END point has been set at the tape end,

 

the playback image will not be frozen

 

properly. Set the END point in a range

 

where pictures have been recorded.

The underlined items indicates the initial setting.

YA93P This appears only when the optional board AJ-YA93P has been installed.

USER menu <INTERFACE>

No./ItemDescription

202This sets the ID information to be returned to the controller.

ID SEL

0000

OTHER :

 

 

0001 DVCPRO :

 

0002

ORIG :

 

Notes:

 

 

• ID information of any VTR except for

 

the DVCPRO’s is set in OTHER.

 

• The ORIG setting should only be used

YA93P

when a Panasonic controller (AG-A850

etc. sold separately) is connected.

– 24 –