Panasonic AJ-SPC700 P Chapter 3 Recording and Playback (continued)

Chapter 3 Recording and Playback (continued)

Removing P2 Cards

1While pressing down the slide lock button, move the slide-out door to the left.

The door opens.

2Tilt down the EJECT button.

3Then, depress the EJECT button to release the P2 card so that you can remove it.

Tilt down the EJECT	Depress the tilted-down
button.	EJECT button to release
	the P2 card.

<Notes>

zWhen a P2 card is being accessed or it is being recognised after insertion (P2 CARD ACCESS LED blinks in orange), do not remove the P2 card.

If your AJ-SPC700P is not set to turn on the P2 CARD ACCESS LED, before removing the card ensure that pre- recording and/or voice memo recording have finished (the P-REC indication has stopped blinking and the V mark or VOICE REC indication on the viewfinder screen has turned off) after stopping recording or playback.

zIf a P2 card being accessed is removed, the viewfinder displays “TURN POWER OFF” and the AJ-SPC700P gives a warning using an alarm and the WARNING LED. In addition, all P2 CARD ACCESS LEDs blink rapidly in green. If this is the case, turn the power off. For more information on warning indications, see [7-3 Warning System].

zIf a P2 card is removed while being accessed, clips on it may become irregular although the data will not be corrupted. Check the clips and restore them if required. For more information about how to restore clips, see [6-9 Restoring Clips].

zIf a P2 card being formatted is removed, it may be not be formatted properly. In this case, the viewfinder displays “TURN POWER OFF”. If this message appears, turn off the power, then restart the AJ-SPC700P to reformat the card.

zIf a P2 card is inserted while another P2 card is being played back, the inserted P2 card is not recognised and the P2 CARD ACCESS LED for that card does not come on. Card recognition starts when the playback ends.

To Prevent Accidental Erasure of P2 Card Content

To prevent the content of a P2 card being accidentally erased, position the write-protect switch on the P2 card at [Protect].

<Note>

Write-protect switchover can be performed while the card is	3
being accessed (during recording or playback), but does not

take effect until access to the card ceases.

			Protect
		Write-protect switch
P2 CARD ACCESS LED and status of P2 cards
P2 CARD	MODE CHECK		Status of P2 Card
ACCESS LED	indication*
Stays on in green	ACTIVE		Writing and reading
			enabled
			Writing and reading
Stays on in	ACTIVE		enabled. The card is
orange			recordable (loop recording
			also enabled).
			Writing and reading
Stays on in			enabled. However, some
	ACTIVE !		clips recorded on the P2
orange or green
			card may not be able to be
			read successfully.
Blinks in orange	ACCESSING		Writing or reading being
			performed.
Quickly blinks in	INFO READING		The P2 card is being
green			recognised.
			The P2 card has no free
	FULL		space. Only reading is
			enabled.
Blinks in green
			The write-protect switch on
	PROTECTED		the P2 card is positioned at
			[PROTECT]. Only reading
			is enabled.
	NOT		The card is not supported
			by your AJ-SPC700P.
	SUPPORTED
			Replace the card.
Stays off
			The P2 card is not properly
	FORMAT ERROR		formatted. Reformat the
			card.
	NO CARD		No P2 card is inserted.

*The mode check indication is shown in the viewfinder. For more information, see [4-7-2 Viewfinder Status Indication Layout].

<For Your Information>

The P2 CARD ACCESS LEDs may be set to stay off using the menu option ACCESS LED. This option can be found on the <SYSTEM MODE> screen, which is accessible from the SYSTEM SETTING page.

23