Panasonic BT-LT2600 manual Input Select

Main Menu (continued)

INPUT SELECT

		The underlined values are factory preset setting values.
Sub menu	Settings	Explanation
VIDEO / Y/C	<AUTO>	Used to select the input format for VIDEO and Y/C input. *1
	<NTSC>	<AUTO>	Either NTSC or PAL is automatically selected.
	<PAL>	<NTSC>	NTSC	<PAL>	PAL
NTSC SETUP	<75>	Selects the NTSC setup level.
	<00>	<75>	Select this when using with a setup signal of
			7.5 IRE. (The inner parts of the monitor are set
			to the 7.5 IRE setup level to suit the black level)
		<00>	Select this when there is no setup level signal.
YPBPR/RGB	<YPBPR>	Selects either YPBPR (Component) or RGB input mode.
	<RGB-VIDEO>	<YPBPR>	Selects the YPBPR signal.
	<RGB-COMP.>	<RGB-VIDEO>Selects the video RGB signal.
		<RGB-COMP.>Selects the PC RGB signal.
COMPONENT	<SMPTE>	Selects YPBPR (Component) signal input level.
LEVEL	<B75>	<SMPTE>	When the signal level specified in SMPTE is
	<B00>		Chroma 100 IRE PB, PR = 0.7 Vp-p.
		<B75>	Select this when connecting a betacam or
			simliar devices set to 7.5 IRE. (The inner parts
			of the monitor are set at 7.5 IRE setup level to
			suit the black level)
		<B00>	Select this when connecting a betacam or similar
			devices that are not setup to the IRE level.
RGB SYNC	<G-ON>	Selects the SYNC when using RGB-VIDEO input.
	<EXT>	<G-ON>	Select when a synchronizing signal is
			superimposed on the G signal.
		<EXT>	Select when an external synchronizing signal is
			received in synchronization.
COMP.		Performs analog PC settings. (Refer to “COMP.” below)

*1 “AUTO” is set when the monitor is shipped from the factory, but if there are concerns about noise etc. from outside the input signal, we recommend assigning specific format.

gCOMP.

The following menus are switched by selecting “RGB-COMP.” in “YPBPR/RGB” in the “INPUT SELECT” menu.

The underlined values are factory preset setting values.

Sub menu	Settings	Explanation
AUTOSETUP*1		Screen automatic adjustment is performed when “RGB-
		COMP.” is selected in “YPBPR/RGB” in the “INPUT SELECT”
		menu. “AUTOSETUP” is performed if a different screen is
		displayed, and “YES” is selected.
H POSITION	<0–60>	Used to adjust the picture display position in the horizontal
	(Factory preset setting: 30)	direction. *2
V POSITION	<0–60>	Used to adjust the picture display position in the vertical
	(Factory preset setting: 30)	direction. *2
PHASE	<0–31>	Used to adjust the clock phase with 1/32 clock phases. *2
	(Factory preset settings:
	J page 28)
CLOCK	<700–1800>	Used to adjust the sampling clock in dot units. *2
	(Factory preset settings:
	J page 28)
WXGA/XGA	<XGA>	Switches between WXGA and XGA.
	<WXGA>

*1 “EXECUTING” is displayed while “AUTOSETUP” is being executed, and “COMPLETE” is displayed when “AUTOSETUP” is completed. If “AUTOSETUP” cannot be completed, “INCOMPLETE” is displayed.

*2 Each “RGB-COMP.” input compatible format can be adjusted, but you cannot load (“SETUP LOAD” J page 21) or save (“SETUP SAVE” J page 21) the user data.

27