31
RQT9184
(ENG)
Power Pag eOperationDisplaysTV screen and video(Continued on the next page)
No power. ≥Insert the AC power supply cord securely into a known acti ve AC outlet. 8
The unit switches to standby
mode.
≥This is a power saving feature. It can be changed if desired using “Off Timer” in the Setup
menu.
≥One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the
unit on.
29
—
Cannot operate the television
or amplifier/receiver.
≥Change the manufacturer code. Some televisions or amplifier/receiver cannot be operated
even if you change the code.
≥It may be necessary to set the manufacturer code again after changing the batteries.
11
11
The remote control doesn’t
work properly. ≥The remote contr ol and main unit are using different codes .
Change the code o n the remote contr ol.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
≥The batteries are depleted. Replace t hem with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Colored glass may obstruct the signal reception/transmission.
≥
Don’t place the signal sensor in direct sunlight or in areas t hat may be subject t o sunlight exposure.
≥It may be necessary to set t he code on the remote control a gain after changing the batte ries.
33
5
5
—
—
11, 33
The unit is on but cannot be
operated.
≥Confirm the cor rect drive is selected .
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [POWER Í/I] on the main un it to switch the unit to sta ndby.
If the unit doesn’t switch to standby, press and hold [POWER Í/I] on t he main unit for
about 3 seconds. The unit is forcibly swit ched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
2 Press [POWER Í/I] on the main un it to switch it on. If the un it still cannot be operated ,
consult the dealer.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
14
—
34
—
—
Play fails to star t even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
≥Insert the disc correc tly with the label facing up.
≥The disc is dir ty.
≥You tried to play a blank disc o r unplayable disc on this unit.
≥[DivX] If playing DivX VOD content, refer to the homepage where you purchased it.
14
36
4, 5
20
Cannot eject disc. ≥The unit may have a problem. While the u nit is off, press and hold [;] and [9/5] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
—
Startup is slow.
When the unit is turned on, audio
and video output takes a long time .
It takes time before play starts.
≥Startup takes time in the following situations.
–Immed iately after a power f ailure or the AC power supply cord is conn ected.
–When the unit is connected with an HDMI cable.
≥[DivX] This is normal on D ivX video.
—
—
Cannot set “On” in “24p
Output”.
≥
Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select “On”. In
some cases where the unit is connected to a TV vi a an amplifier/receiver through the HDMI terminals,
you may not be able to select “On”. In this case, connect the unit to a TV through the HDMI terminal and
connect it to the amplifier/receiver through any terminal other than HDMI.
28
The display is dim. ≥Change “FL Display” in the Setup menu. 27
The elapsed time displayed is
actually less than the play time .
≥The displayed play tim e is converted from the number of frame s at 29.97 frames (e qual to
0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as
approximately 59 minute s 56 seconds).
—
The images from this unit do
not appear on the television.
Picture is distorted.
≥Make sure that the television is connected to the VIDEO OUT te rminal, S VIDEO OUT
terminal, COMPONENT VID EO OUT terminals or HD MI AV OUT terminal on this unit.
≥Make sure that the television’s input setting (e.g., VIDEO 1) is c orrect.
≥
An incorrect resolution is selected in “Component Video Resolution”, when the television is connected
to
COMPONENT VIDEO OUT
terminals. While stopped, press and hold [
∫
]
and [
1
](PLAY)
on the
main unit at the same time for more than 5 seconds to cancel this setting. Set the item again.
≥If “24p Output” is set to “O n” when the unit is conne cted to a TV through any ter minal other
than HDMI, images may not d isplay properly. In this case, set “24 p Output” to “Off”.
≥[DivX] Images may not be outp ut due to how files wer e created.
6, 7
—
28
28
—
Picture stops. ≥[DivX] Picture may stop if the DivX files are greater than 2 GB. —
The screen change s
automatically.
≥When the “Screen Save r Function” in the S etup menu is set to “On”, the display may r eturn to
the screen saver mod e automatically if there is no operati on for 10 minutes or m ore.
27
Video is not output in high
definition.
≥High definition vi deo cannot be output through the VIDEO OUT or S VIDEO OUT terminals.
≥Confirm that the “HDMI Video Mode” , “HDMI Resolution”, and “Component Vi deo
Resolution” in th e Setup menu are se t properly.
≥The video output resolut ion is restricted to “480p” when DVD-Video is output from the
COMPONENT VIDEO OUT terminals.
—
28
—
Status messages do not appear.
≥Select “Automatic” in “Status Messages” in the Setup menu. 27
Reference
DMP-BD50PP-RQT9184_eng.book 31 ページ 2008年4月4日 金曜日 午後8時14分