Panasonic DMR-E75V operating instructions Error messages, Common, On the unit’s display, On the TV

Helpful Hints	DVD	VHS
Error messages
∫ Common
On the unit’s display			Page
H, F	≥An error has occurred. The number following “H” or “F” depends on the status of the		–
(“” stands for a number.)	unit.
	Reset procedure:
	Press [POWER Í/I] to switch the unit to standby mode and then back to ON.
	Alternatively, press [POWER Í/I] to switch the unit to standby mode, disconnect the
	AC power supply cord, and then reconnect it.
	≥If the service numbers fail to clear, note the service numbers and contact a qualified		–
	service person.
∫ DVD
On the TV			Page
Cannot finish recording completely.	≥The program was copy-guarded.		–
	≥The disc may be full.		–
Cannot play.	≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).		–
Cannot record on the disc.	≥The disc may be dirty or scratched.
Unable to format.			19
Please check the disc.
Cannot record. Disc is full.	≥Create space by erasing any unwanted titles. [RAM]		23, 33, 37
Cannot record. Maximum number	≥Use a new disc. [RAM] [DVD-R]		–
of titles exceeded.
Error has occurred. Please press	≥Press [ENTER] to start recovery process. You cannot operate the unit while it is		–
ENTER.	recovering (“SLF CHECK” appears on the unit’s display).
No disc.	≥You haven’t inserted a disc. Correctly insert a disc that this unit can play.		18, 20
	≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.		20
Please change the disc.	≥There may be a problem with the disc. Press [<, OPEN/CLOSE] to remove it and		19
	check it for scratches or dirt. (The unit turns off automatically after you open the tray.)
This is a non-recordable disc.	≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized		–
	DVD-R.
This disc is not formatted properly.
	≥You inserted an unformatted DVD-RAM. Format the disc with this unit.		31
	≥The operation is prohibited by the unit or disc.		21
On the unit’s display			Page
 CHK REMOTE	≥The remote control and main unit are using different codes. Change the code on the		17
(“” stands for a number.)	remote control or main unit.
HARD ERR	≥If there is no change after turning the unit on and off, consult the dealer where the unit		–
	was purchased.
NO READ	≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.		19
	≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [<, OPEN/		19
	CLOSE] to eject the disc.
PROG FULL	≥There are already 16 timer programs. Delete unnecessary timer programs.		29, 53
SLF CHECK	≥There was a power failure or the AC plug was disconnected while the unit was on. The		–
	unit is carrying out its recovery process. Wait until the message disappears.
UNSUPPORT	≥You have inserted a disc the unit cannot play or record on.		19
U14	≥The unit is hot.
	The unit switches to standby for safety reasons. Wait for about 30 minutes until the
	message disappears.		–
	Select a position with good ventilation when installing the unit. Do not block the cooling
	fan on the rear of the unit.
U99	≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the		–
	unit to standby. Now press [POWER Í/I] again to turn the unit on.
∫ VHS
On the TV			Page
PLEASE PUT IN A VIDEO	≥A video cassette is not inserted when recording programs or setting the timer		48
CASSETTE.	recording. Insert a video cassette with an intact erasure prevention tab.
PLEASE SET THE CLOCK	≥The clock is not set when recording programs or setting the timer recording. Set the		46
	clock.
PLEASE USE A CASSETTE WITH	≥A video cassette without the intact erasure prevention tab is inserted when recording
TAB.	programs or setting the timer recording. Use a video cassette with an intact erasure		48
	prevention tab.

65