Starting to use
Turning on the power
Please ensure that all preparations have been completed before turning on the power. (Refer to pages 21 – 25.)
#Remove the lens cover.
*Turn the focus ring and the zoom knob to adjust the projected image focus and size.
Focus |
Zoom |
$Connect the accessory power cord. |
| |
%Press the MAIN POWER switch to | % | |
the “” side to turn on the power. | ||
| ||
The power indicator on the projector | $ | |
will illuminate red. |
|
&Press the POWER button.
The power indicator on the projector | RGB INPUT LAMP | TEMP |
|
| |||
POWER | AUTO SETUP | INPUT | SHUTTER | POWER SETUP | |||
will flash green. After a short period, |
| AUTO | |||||
ON(G) |
|
|
| VIDEO | MENU | ||
|
|
|
|
|
| RGB | LASER |
|
| STANDBY(R) |
|
|
|
|
|
the indicator will illuminate green, and |
|
|
|
| PAGE | ||
MENU |
|
| ENTER |
|
| ||
a picture will be projected. |
|
|
|
|
|
|
|
'Press the input select (INPUT, RGB, | RGB INPUT | LAMP | TEMP |
|
|
| |
VIDEO) button to select the input | POWER | AUTO SETUP | INPUT | SHUTTER | AUTO |
| |
|
|
|
|
|
| POWER SETUP | |
signal. |
|
|
|
|
| RGB LASER | |
| STANDBY(R) |
|
|
|
|
| |
|
| ON(G) |
|
|
| VIDEO MENU |
|
The input signal selected will change |
|
|
|
| PAGE |
| |
MENU |
| ENTER |
|
| |||
as shown at below each time an input |
|
|
|
|
|
| |
select button is pressed. |
|
|
|
|
|
|
|
INPUT | VIDEO |
| RGB |
|
|
|
|
(While pressing the adjuster buttons, adjust the forward/back angle of tilt of the projector.
Turning off the power
#Press the POWER button. “POWER OFF” is
displayed on the screen. |
| POWER | OFF |
| ||
| OK |
| CANCEL |
| Operation | |
$Select “OK” using the I and H buttons and |
|
|
| |||
|
|
|
|
|
| |
press the ENTER button. |
|
|
|
|
| |
The lamp unit will switch off and the picture will stop being projected. (The |
| |||||
power indicator on the projector will illuminate orange.) |
|
|
|
|
| |
%Wait until the power indicator on the projector illuminates red (until | Basic | |||||
the cooling fan stops). |
|
|
|
| ||
|
|
|
|
| ||
Do not in any way cut power to the projector while the cooling fan is still operating. Be careful not to switch off the MAIN POWER switch of the projector, unplug the power cord from the electrical outlet or turn off
&Press the MAIN POWER switch to the “O” side to turn off the power.
NOTE:
BAfter the power is turned off, the lamp unit will take some time to cool |
down. If you turn the power back on again before the lamp unit has cooled |
down, the lamp unit may not turn on straight away, but it will turn on |
automatically after a short period. (During this time, the power indicator on |
the projector will flash orange.) |
BWhen the projector is in standby mode (the power indicator on the |
projector is illuminated red), the projector will still draw a maximum 1.7 W |
of power, even when the cooling fan has stopped. |
BIf the MAIN POWER switch is accidentally turned off while the projector is |
being used, the lamp unit may not turn on straight away after the power is |
turned back on. In such cases, the lamp unit will turn back on |
automatically after a short period. (During this time, the power indicator on |
the projector will flash green.) |
BA tinkling sound may be heard while the power indicator is turned off, but |
)Press the AUTO SETUP button to initiate automatic positioning.
If keystone distortion has not been corrected to the optimum level, carry out keystone correction as described on page 33.
RGB INPUT LAMP TEMP
POWER | AUTO SETUP | INPUT | SHUTTER | AUTO |
|
|
| POWER SETUP | |
|
|
| RGB | LASER |
STANDBY(R) |
|
| VIDEO | MENU |
ON(G) |
|
| ||
|
|
| PAGE | |
MENU |
|
| ENTER |
|
this is not a sign of a malfunction. |
BYou can also turn off the power by pressing the POWER button twice or |
by holding down it for at least 0.5 seconds. |
26 | 27 |
