Option settings
Use the F and G buttons on the projector or remote control unit to select an item, then press the I or
Hbuttons to change the setting.
| OPTION1 | |||
OSD |
|
|
| ON |
|
|
|
|
|
AUTO | KEYSTN | ON | ||
|
|
|
|
|
AUTO | RGB | IN | ON | |
|
|
|
|
|
RGB2 | SELECT | INPUT | ||
|
|
|
|
|
RGB/Y•PB•PR | Y•PB•PR | |||
|
|
| ||
SXGA | MODE | SXGA | ||
SELECT |
| ADJ | ESC | |
| ||||
| OPTION2 | |||
|
|
| ||
BACK | COLOR | BLUE | ||
|
|
|
|
|
FRONT/REAR | FRONT | |||
|
|
|
|
|
DESK/CEILING | DESK | |||
|
|
| ||
FAN | CONTROL | STANDARD | ||
|
|
|
|
|
LAMP | POWER | HIGH | ||
LAMP | RUNTIME | 10H | ||
|
|
|
|
|
FUNC | 1 |
|
| INDEX |
|
|
| ||
CONTROL | KEY | ON | ||
SELECT |
| ADJ | ESC | |
OSD
ON
The current input name is displayed in the
OFF
Use this setting when you do not want the current input name to be displayed.
AUTO KEYSTN
This should normally be set to ON.
ON
During automatic setup, the angle of tilt of the projector is detected and keystone distortion is corrected automatically.
OFF
Use this setting when you do not want automatic keystone correction
to be carried out during automatic setup, such as when the screen itself is at an angle.
AUTO RGB IN
This should normally be set to ON.
ON
During automatic setup, the projector selects whichever one of the RGB1 IN or RGB2 IN connectors has a signal being input, and uses that signal for projection. (If a picture is being projected, the signal source is not automatically changed.)
OFF
Use this setting when you do not want the signal source to be changed automatically during automatic setup.
RGB2 SELECT
RGB2 SELECT 
INPUT
[
OUTPUT
This setting is used to select the function of the RGB2 IN/RGB1 OUT connector.
RGB/Y·PB·PR
RGB/Y•PB•PR RGB
[
Y•PB•PR
This setting is valid when HDTV, 525p (480p) and some VGA480 signals are being input. Select the setting in accordance with the input signal.
SXGA MODE
SXGA MODE | SXGA |
| [ |
| SXGA+ |
This setting is only for an SXGA signal.
SXGA
Select this item normally.
SXGA+
When the projected image is contracted vertically, select this item.
BACK COLOR
BACK COLOR | BLUE |
| [ |
| BLACK |
This sets the color which is projected onto the screen when no signal is being input to the projector.
FRONT/REAR
FRONT/REAR 
FRONT
[
REAR
This setting should be changed in accordance with the projector
Set to “FRONT” when using a normal reflective screen with the projector positioned in front of the screen, and set to “REAR” when using a translucent screen with the projector positioned behind the screen.
DESK/CEILING
DESK/CEILING 
DESK
[
CEILING
This setting should be changed in accordance with the projector
Set to “DESK” when setting up the projector on a desk or similar, and set to “CEILING” when suspending
the projector from the ceiling using the ceiling bracket which is sold separately.
FAN CONTROL
FAN CONTROL 
STANDARD 
[
HIGH
If using of this projector at high elevations (above 1400 m), set FAN CONTROL to “HIGH”.
LAMP POWER
LAMP POWER | HIGH |
| [ |
| LOW |
This setting changes the lamp brightness. When set to “LOW”, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp’s operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the LAMP POWER to “LOW”.
LAMP RUNTIME
This setting displays the usage time for the lamp unit which is currently being used.
NOTE:
BThe lamp’s operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off).
Advanced Operation Advanced Operation
40 | 41 |
