Tape Operation | Tape Operation |
• Tape
Search System
For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.
Repeat Play
Set to playback a recording over and over.
1 Press ACTION to display menu.
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes of recorded tape.
1 Press CM/ZERO in Play mode.
Operation
Index Search
1 |
| SEARCH | |
INDEX |
| PROGRAM END | |
|
| ||
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH
EXIT :STOP
2 | INDEX SEARCH |
FORWARD SEARCH :FF
REVERSE SEARCH :REW
Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number.
•To calculate number, see below.
Press FF or REW on the remote to start search.
Play begins at search end. To search forward or back 1 index, press
FFor REW on the remote or VCR while screen left is displayed (10 sec.).
•To cancel, press PLAY or STOP.
Program End Search
Locates end point of recording for continuity.
1 Press SEARCH twice to display SEARCH
in Stop or Play mode.
2 |
| SEARCH | Press FF on the remote | |
INDEX |
| PROGRAM END | to start PROGRAM | |
|
|
|
| |
|
|
|
| END SEARCH. |
| SEARCH START :FF | • To cancel, press | ||
|
|
|
| |
| EXIT :SEARCH | PLAY or STOP. | ||
Examples of Program End Search.
Fig. 1
Program 1 | INDEX | Program 2 or BLANK |
the current tape position Press SEARCH button
| End Point |
FF |
Fig. 2 |
|
|
|
|
|
INDEX | Program 1 | BLANK | INDEX | Program 2 | BLANK |
|
| the current tape position |
|
| |
|
| Press SEARCH button |
|
| |
|
|
| FF |
| End Point |
2 |
|
|
|
|
|
|
| Press |
VCR |
|
| CLOCK |
| CHANNEL |
| ||
| REPEAT | PLAY | :OFF |
| to select REPEAT PLAY | |||
| REMOTE WARNING | :ON | ||||||
| AUTO SHUT- OFF | :OFF | and press to set ON | |||||
| IDIOMA/LANGUE : ENGLISH | |||||||
| VCR’ S OUTPUT CH | :3 |
| or OFF. | ||||
|
|
|
|
|
|
|
| |
| SELECT : | SET : | ON : Play repeats at | |||||
| EXIT : ACT I ON |
|
| |||||
tape end or if unrecorded portion over 30 sec. is detected.
3 Press ACTION to return to normal screen.
Zero Search
To quickly return to a specified tape location.
1 Press DISPLAY during play
to display Counter.
2 | PLAY 12 : 0 0AM | 0 : 00 : 00 | Press RESET |
| COUNTER at desired | ||
| SP | ||
|
|
| position to reset to |
|
|
| “0:00:00”. |
•Press CM/ZERO repeatedly to change skip time as shown below.
PLAY
1st Press 
1 min Skip
2nd Press | 2 min Skip |
3rd Press 
3 min Skip
• No indication appears.
To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1 | 2 | 3 | 4 |
| 5 | 6 | 7 |
Fig. 3 |
|
|
|
|
| ||
|
| the current tape position |
| ||||
|
| Press SEARCH button |
| ||||
|
|
|
|
|
|
|
|
| INDEX | Program 1 |
|
| BLANK |
| Program 2 |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| If search |
End Point |
| FF |
|
| exceeds a few |
|
|
|
| ||
|
|
|
| ||
|
|
|
|
| seconds in |
|
|
|
|
| BLANK area. |
3 | Continue to record, playback, etc. | |
4 | Press STOP. |
|
5 | REW 12 : 3 0AM CH 02 | Press CM/ZERO in Stop |
0 : 30 : 30 | mode to start ZERO | |
SP | ||
SEARCH.
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1 | 2 | 3 | 4 | 5 | 6 | 7 |
|
|
|
|
|
|
|
NOTE: 
indicates start points of each recording.
Note
•If Index Search is started very close to an index mark, that index mark may not be counted in the search.
Upon locating end point,
➛search continues 7 sec. past end point,
➛tape rewinds to 10 sec. before end point,
➛tape plays to end point and stops.
Notes
•If Program End Search is started very close to an index mark, that mark may be skipped over.
•To cancel, press PLAY or STOP.
• Unit will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
- 6 - | - 7 - |
