Specifications (DIN 45 500)
Specifications/Help messages ENGLISH
AMPLIFIER SECTION
Power output (at AC 230 to 240 V) |
|
DIN 1 kHz (T.H.D. 1 %) | 2 x 125 W (4 Ω) |
20 Hz to 20 kHz continuous power output |
|
both channel driven | 2 x 80 W (6 Ω) |
Total harmonic distortion |
|
rated power at 20 Hz to 20 kHz | 0.09 % (6 Ω) |
Power bandwidth |
|
both channel driven, | 4 Hz to 88 kHz (6 Ω, 0.9 %) |
Power output each channel driven (at AC 230 to 240 V) | |
DIN 1 kHz (T.H.D. 1 %) |
|
Front (L/R) | 100 W (6 Ω) |
Center | 100 W (6 Ω) |
Surround (L/R) | 100 W (6 Ω) |
Surround Back (L/R) | 100 W (6 Ω) |
Load impedance |
|
Front (L/R) |
|
A or B | 4 Ω to 16 Ω |
A and B | 6 Ω to 16 Ω |
| 4 Ω to 16 Ω |
Center | 6 Ω to 16 Ω |
Surround (L/R) | 6 Ω to 16 Ω |
Surround Back (L/R) | 6 Ω to 16 Ω |
Frequency response |
|
CD, BD/DVD, DVD Recorder, VCR, TV/STB, AUX | 4 Hz to 88 kHz, ±3 dB |
DVD 6CH | 4 Hz to 44 kHz, ±3 dB |
Input sensitivity and impedance |
|
CD, BD/DVD/DVD 6CH, DVD Recorder, VCR, TV/STB, AUX 200 mV/22 kΩ | |
S/N at rated power (6 Ω)
CD, TV/STB, BD/DVD PLAYER, DVD Recorder (Digital input)
|
| 90 dB (IHF, A: 103 dB) |
Tone controls |
|
|
BASS |
| 50 Hz, +10 dB to |
TREBLE |
| 20 kHz, +10 dB to |
Channel balance (250 Hz to 6.3 kHz) | ±1 dB | |
Channel separation |
| 55 dB |
Subwoofer frequency response | 7 Hz to 200 Hz | |
|
|
|
Digital input | (OPTICAL) | 2 |
| (COAXIAL) | 2 |
|
|
|
HDMI (Version 1.2a) | Input | 2 |
| Output | 1 |
|
| |
FM TUNER SECTION |
| |
Frequency range |
| 87.50 MHz to 108.00 MHz |
Sensitivity |
|
|
S/N 30 dB |
| 1.5 µV/75 Ω |
S/N 26 dB |
| 1.3 µV/75 Ω |
S/N 20 dB |
| 1.2 µV/75 Ω |
IHF usable sensitivity (IHF ’58) | 1.5 µV/75 Ω | |
Help messages
IHF 46 dB stereo quieting sensitivity | 22 µV/75 Ω |
Total harmonic distortion |
|
MONO | 0.2 % |
STEREO | 0.3 % |
S/N |
|
MONO | 60 dB |
STEREO | 58 dB |
Frequency response | 20 Hz to 15 kHz, +1 dB, |
Alternate channel selectivity | ±400 kHz, 65 dB |
Capture ratio | 1.5 dB |
Image rejection at 98 MHz | 40 dB |
IF rejection at 98 MHz | 70 dB |
Spurious response rejection at 98 MHz | 70 dB |
AM suppression | 50 dB |
Stereo separation | 40 dB |
Carrier leak | 19 kHz, |
| 38 kHz, |
Channel balance (250 Hz to 6.3 kHz) | ±1.5 dB |
Limiting point | 1.2 µV |
Bandwidth |
|
IF amplifier | 180 kHz |
FM demodulator | 1000 kHz |
Antenna terminal | 75 Ω (unbalanced) |
AM TUNER SECTION |
|
Frequency range | 522 kHz to 1611 kHz (9 kHz steps) |
| 530 kHz to 1620 kHz (10 kHz steps) |
Sensitivity | 20 µV, 330 µV/m |
Selectivity (at 999 kHz) | 55 dB |
IF rejection (at 999 kHz) | 50 dB |
VIDEO SECTION |
|
Output voltage at 1 V input (unbalanced) | 1± 0.1 |
Maximum input voltage | 1.5 |
Input/output impedance | 75 Ω (unbalanced) |
| |
Input | DVD, DVD Recorder, TV/STB |
Output | TV MONITOR |
Component Video |
|
Input | DVD Recorder, TV/STB |
Output | TV MONITOR |
GENERAL |
|
Power supply | AC 230 to 240 V, 50 Hz |
Power consumption | 140 W |
Dimensions (W x H x D) | 430 mm x 107.5 mm x 390 mm |
Mass | 4.7 kg |
Power consumption in standby mode: | 0.9 W |
Power consumption in HDMI off mode: | 0.35 W |
Notes:
1.Specifications are subject to change without notice.
2.Mass and dimensions are approximate.
3.Total harmonic distortion is measured by the digital spectrum analyzer.
RQTV0247
38
Message | Causes and solutions |
|
|
| Muting is on. |
| Press [MUTING] on the remote control to cancel (➡ page 31). |
|
|
| You are trying to use a feature that is available only in “MUSIC” mode. |
| Change the mode to “MUSIC” (➡ pages 22 to 23). |
|
|
| Center and surround speakers are not connected, or they are set as absent. |
| Connect the speakers (➡ page 13) or change their setting to present (➡ page 27). |
|
|
| Surround and surround back speakers are not connected, or they are set as |
| absent. Connect the speakers (➡ page 13) or change their setting to present |
| (➡ page 27). |
|
|
| Surround back speakers are not connected, or they are set as absent. Connect |
| the speakers (➡ page 13) or change their setting to present (➡ page 27). |
|
|
| You are trying to use an effect unavailable with |
|
|
| You are trying to use an effect unavailable with |
|
|
| You are trying to use an effect unavailable with DVD analogue |
|
|
| You are trying to use an effect unavailable with the current input source. |
|
|
(flashing) | You have set the “PCM FIX” mode. Cancel this mode (➡ page 28). |
| |
|
|
| SPEAKERS A is off. Press [SPEAKERS A] to turn on “SPEAKERS A” (➡ page |
| 18). |
|
|
| SPEAKERS A and SPEAKERS B are off. Select one of the speakers (➡ page |
| 18). |
|
|
