20
≥Do not drop or insert metal or flammable objects inside
the SD Mobile Printer.
≥Do not splash or wet the SD Mobile Printer.
≥Do not disassemble or remodel the SD Mobile Printer.
≥Do not touch the metal parts on the SD Mobile Printer or
the plug during a thunderstorm.
≥Do not unplug with wet hands.
≥Do not place the SD Mobile Printer in locations with
smoke, steam, high humidity, large amounts of dust, or
severe vibrations.
≥Do not install the SD Mobile Printer in such a way that
the power Cable is forcibly bent.
≥Do not place heavy objects on the SD Mobile Printer
≥Do not move the SD Mobile Printer with the power Cable
plugged in.
≥Do not unplug by pulling on the power Cable.
≥Remove the plug from the outlet as a safety measure
when cleaning the SD Mobile Printer or when the SD
Mobile Printer will not be used for a long period of time.
≥A minute amount of current is consumed even when the
SD Mobile Printer power is off.
≥Do not touch any internal components other than those
specified.
≥During printing, the paper moves forward and backward
several times. You can be cut if you touch the paper
during this operation.
≥Do not forcibly pull out the Ink Cassette or paper, shake
the printer, or add more paper while printing is in
progress.
≥Printing in cold or hot temperatures may take a little
more time.
ªNotes on Handling Finished P rints
In order to preserve finished prints in the best condition,
always observe the following points. Failure to observe
these points could result in a deterioration of print quality
or injury.
≥Do not affix cellophane tape to the printed surface. In
particular, be careful not to let plastic desk pads,
business card cases, or plastic erasers come into
contact with the printed surface.
≥A sheet of paper printed is protected by the overcoat.
However, rubbing the surface with a hard object and
scratching will cause surface flaws or color fade-out.
≥Do not touch the printed surface with your fingers.
≥Do not spill or apply volatile solvents such as alcohol to
the printed surface. Doing so could result in
discoloration or fading.
≥Do not leave printed surfaces in contact with one
another. Doing so could cause color transfer between
the two images. Color transfer could also occur if a
printed surface is left in contact with any other type of
paper under pressure for an extended period of time.
≥Do not store prints under conditions of high
temperatures or high humidity. Leaving prints under
such conditions for an extended period of time could
cause a deterioration in print quality. Do not leave prints
exposed to direct sunlight.
≥Do not scratch the printed surface.
ªOptimal Use of the Battery
Battery Characteristics
This Battery is a rechargeable lithium ion battery. Its
ability to generate power is based upon the chemical
reaction that takes place inside it. This reaction is
susceptible to the surrounding temperature and humidity,
and, if the temperature is too high or too low, the operating
time of the Battery becomes shorter. If the Battery is used
in an extremely cold environment, the Battery may
operate only for about 5 minutes. If the Battery becomes
extremely hot, a protective function may operate, and the
Battery may become unusable for a while.
Be Sure to Detach the Battery after Use
Be sure to detach the Battery from the SD Mobile Printer.
(If it is left attached to the SD Mobile Printer, a minute
amount of current is consumed even when the SD Mobile
Printer power is off.) If the Battery is left attached to the
SD Mobile Printer for a long time, over discharge takes
place. The Battery may become unusable after it is
charged.
Disposing of an Unusable Battery
≥The Battery has a limited life.
≥Do not throw the Battery into fire because it may cause
an explosion.
Always Keep the Terminals of the Battery Clean
Prevent the terminals from getting clogged with dirt,
dust, or other substances.
If you drop the Battery accidentally, check to see if the
Battery body and terminals are deformed.
Attaching damaged Battery to the SD Mobile Printer
may damage the SD Mobile Printer.
Cautions for Storage
≥Extremely high temperatures or low temperatures will
shorten the life of the Battery.
≥If the Battery is kept in smoky or dusty places, the
terminals may rust and cause malfunctions.
≥Do not allow the Battery terminals to come in contact
with metal objects (such as necklaces, hairpins, etc.)
This can result in a short circuit or heat generation and,
if you touch the Battery in this condition, you may be
badly burned.