Panasonic WV-CS954 operating instructions Preset ID Setting Preset ID

** POSITION 1 **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

PAN OFFSET SET ← 0 →

RET TOP

FLOOR1

DOOR

3.Use the joystick to position the camera, and then press the CAM (SET) button.

** POSITION 1 **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

U TILT D/L PAN R

PAN OFFSET SET ← 0 →

RET TOP

FLOOR1

DOOR

4.Move the cursor to → PUSH SET to the right of ZOOM/FOCUS, and then press the CAM (SET) button to display the ZOOM/FOCUS setting menu.

** POSITION 1 **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

U ZOOM D/L FOCUS R

PAN OFFSET SET ← 0 →

RET TOP

FLOOR1

DOOR

5.Move the joystick left, right, up and down to adjust the position of the lens focus, and then press the CAM (SET) button.

Notes:

•Focusing may be difficult when the camera is at an angle that is close to horizontal.

•A different position number can be selected by moving the cursor to the position number at the top of the position setting menu and tilting the joystick left and right. Pressing the CAM (SET) button will change to the setting screen for the newly selected position number.

•The currently registered camera ID and preset ID appear at the bottom of the position setting menu.

•When using a system device other than the WV- CU650/CU950*, WJ-HD309A/HD316A over 65 position numbers cannot be set. (as of February 2005)

*Operation procedure may vary depending on the version of the system controller's software. For Ver.1.xx or earlier: only camera function operations are supported

For Ver.2.xx or later: PRESET/PGM PRESET button is also supported

Align the cursor here

** POSITION 1* **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

PAN OFFSET SET ← 0 →

RET TOP

FLOOR1

DOOR

●Adjusting Camera Position When Changing Cameras (PAN OFFSET SET)

The system controller etc. has a function for downloading (saving) and uploading (recovering) setting information for the camera. This function allows you to upload (recover) original setting information that has been downloaded (saved) before some unforeseen damage or malfunction causes setting information in the camera to be lost. However, there may be some slight differences in images from those uploaded (recovered) when the camera is changed. The "PAN OFFSET SET" function is for adjusting these differences.

1.Align the cursor with "PAN OFFSET SET" with the ← or → arrow, and press the CAM (SET) button to set

the offset value.

Set the offset value to 0.0, or in a range of -10 to +10. All preset positions for the camera's position are adjusted according to the offset value.

Important: Data is not compatible with existing cameras. Uploading setting information from existing cameras will damage data in the camera. If data in the camera is damaged, download camera setting information from a camera that still has the factory settings and then upload it to the camera with the damaged data.

●Preset ID Setting (PRESET ID)

The preset ID is a series of alphanumeric characters that indicate the location of the camera. This item can be used to turn display of the preset ID on the monitor screen on or off, and to input the preset ID.

1.Move the cursor to PRESET ID, and then tilt the joystick left or right to toggle preset ID display on and off.

PRESET NO.		1*
POSITION SET
PRESET ID	ON
ALC/MANUAL	ALC
AF MODE	MANUAL L
DWELL TIME	10S
SCENE FILE	OFF
PRESET SPEED	••••••••I
	L		H

RET TOP DEL

2.Select ON or OFF, and then press the CAM (SET) button.

This will display the preset ID setting menu.

3.Use the joystick to move the cursor the character you want to input, and then press the CAM (SET) button. The text input procedure is the same as that for camera ID input.

See steps 3 through 5 under “(1) Camera ID (CAMERA ID)” on page 22 for information about inputting the text for the preset ID and specifying its position on the display.

-28-