|
|
|
|
|
|
|
| FIGURE 6 | |
STEP 6: |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 6 | 7 | 22 |
|
• Insert two 1/2” FLANGE BEARINGS (40) into |
|
|
|
|
| ||||
|
|
|
|
|
| ||||
| the LEFT PRESS HANDLE (7) as shown in |
|
|
|
|
|
| ||
| FIGURE 6 |
|
|
|
| 22 | FLUSH SIDE |
| |
|
|
|
|
|
|
| |||
• Using hammer tap one 5/16 X 2” ROLL PIN (47) |
|
|
|
|
|
| |||
| thru LEFT PRESS HANDLE (7) until it is flush |
|
|
|
|
|
| ||
| with other side of HANDLE as shown in |
|
|
|
|
|
| ||
| FIGURE 6 |
|
|
|
|
|
|
|
|
• Repeat STEP 6 for the RIGHT PRESS |
|
|
|
|
|
| |||
| ARM HANDLE (6) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 47 |
|
|
|
|
|
|
| 40 |
|
|
|
|
|
STEP 7: |
|
| NOTE: |
|
|
|
|
| |
|
|
|
| Place PRESS ARM (8) | upside down on floor as shown to complete this step | ||||
• | Place LEFT PRESS HANDLE (7) onto PRESS |
|
| 34 |
|
|
| ||
| ARM (8). Make sure that the 5/16 X 2” ROLL |
|
|
|
|
|
| ||
| PIN (47) passes into the slot located in the plate |
|
|
|
|
|
| ||
| of the PRESS ARM (8) |
|
|
|
| 36 |
|
|
|
• Once in place secure and tighten the LEFT |
|
|
|
|
| ||||
|
|
|
|
|
| ||||
| PRESS HANDLE (7) to PRESS ARM (8) |
|
|
|
|
|
| ||
| using one 3/8” WASHER (36) and one |
|
|
|
|
|
| ||
| 3/8” LOCK NUT (34) |
|
| 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• | IMPORTANT! Do not overtighten: PRESS |
|
|
|
| 47 | 7 | ||
| ARM should rotate freely |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
• Repeat STEP 7 for the RIGHT PRESS |
|
|
|
| SLOT |
| |||
| ARM HANDLE (6) |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
| 8 |
|
|
|
|
|
|
|
|
| FIGURE 7 |
|
|
|
|
|
| 1/2 | 1 | 1/2 | 1/2 | 1/2 | 1/2 | 5 | 1/2 | 6 |
| 0 | 2 | 3 |
| 4 |
| |||
|
|
|
| 9 |
|
|
|
|
|
