Paradyne 3166 CSU, 3166 DSU E-12

SNMP MIB Objects

E-12 3166-A2-GB20-10November 1998

Near End Group – “dsx1LoopbackConfig” Object (dsx1ConfigEntry 9)

This object specifies the loopback state of the T1 interface. Only the following

values are supported by the DSU/CSU.

dsx1NoLoop(1) – The T1 interface is not in a loopback state.

dsx1PayloadLoop(2) – Specifies that a Payload Loopback (PLB) is active for

the network interface or a Repeater Loopback (RLB) is active for the DTE

Drop/Insert (DSX-1) interface.

dsx1LineLoop(3) – Specifies that a Line Loopback (LLB) is active for the

network interface or a DTE Loopback (DLB) is active for the DTE Drop/Insert

(DSX-1) interface.

Near End Group – “dsx1LineStatus” Object (dsx1ConfigEntry 10)

This object specifies the line (alarm) status of the T1 interfaces. Only the

following values are supported by the DSU/CSU. More than one value may be

active at a time.

dsx1NoAlarm(1) – No alarm present.

dsx1RcvFarEndLOF(2) – A yellow alarm signal is being received.

dsx1RcvAIS(8) – An Alarm Indication Signal (AIS) is being received.

dsx1LossOfFrame(32) – An Out Of Frame condition has persisted for more

that 2.5 seconds (i.e., Red Alarm).

dsx1LossOfSignal(64) – A Loss of Signal condition has persisted for more

that 2.5 seconds (i.e., Red Alarm).

dsx1LoopbackState(128) – The near end of the T1 interface is in a loopback

state.

dsx1Other Failure(4096) – An Excessive Error Rate (EER) has been

detected on the network interface.

Near End Group – “dsx1SignalMode” Object (dsx1ConfigEntry 11)

This object specifies whether Robbed Bit Signaling (RBS) is being used. This

object differs from the MIB definition in that it is “read-only” (not read/write) for

DSU/CSUs. Only the following values are supported by the DSU/CSU.

none(1) – No signaling is being used on this interface.

robbedBit(2) – Robbed Bit Signaling is being used on at least one DS0 on

this T1 interface.

Contents

Main Page B Important Safety Instructions Page D Government Requirements and Equipment Return United States NOTICE TO USERS OF THE UNITED STATES TELEPHONE NETWORK 3166 DSU/CSU Facility Interface Codes Code Description E Canada NOTICE TO USERS OF THE CANADIAN TELEPHONE NETWORK Warranty, Sales, and Service Information CAUTION: i Contents About This Guide 1 Introduction 2 Installation ii 3 SDCP Operation iii 4 Monitoring and Testing Page v E SNMP MIB Objects F IP Networking Address Scenario Page vii About This Guide Pin Assignments. Configuration Options. Technical Specifications SDCP Menu. Product-Related Documents Document Number Document Title ix Reference Documents Page 1-1 Introduction 1 COMSPHERE 3000 Series Carrier Installation Manual Features 1-2 Alarm Message Capability Front Panel Emulation Asynchronous Terminal Interface (ATI) Support Telnet Access SNMP Management Support Physical Description Rear Connector Module Circuit Card and Front Panel Table 1-1. 3166 DSU/CSU Rear Connector Module Connectors Name Function Page 2-1 Installation 2 Important Instructions Important Safety Instructions !HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES Installation 2-3 2-4 Pin Assignments Installation 3166-A2-GB20-10 November 1998 2-5 98-16080 NET DIAGNOSTIC CHANNEL Network 2-6 98-16081 DSU/CSU 3166 3-1 SDCP Operation 3 Front Panel Emulation COMSPHERE 3000 Series Carrier Installation Manual Using the SDCP 3-2 LCD Device Health and Status Keypad 3-3 Test Jacks Test Jacks System 3-4 LEDs BLINKING FAST BLINK: BLINKING: Network Interface 3-5 Table 3-2. Network Interface (NET) LEDs ON Data Port 3-6 Table 3-3. Data Port (Port1) LEDs CYCLING: 3-7 Displaying Unit Identity xxxx xxxxxxx xxx 3-8 3-9 Setting Customer Identification 3-10 Displaying LED Conditions Front Panel Emulation 3-11 Changing Configuration Options 3-12 3-13 Displaying/Editing Configuration Options 3-14 3-15 Saving Edit Changes 3-16 Enabling the Communication Port 3-17 3-18 Table 3-4. Control Sequence Sequence ASCII HEX 3-19 Configuring the DSU/CSU for SNMP or Telnet Access IP Network Addressing Scenarios 3-20 Selecting the Port 3-21 Setting the IP Address xxx.xxx.xxx.xxx IP Network Addressing Scenarios 3-22 000.000.000.000 3-23 Selecting the Link Layer Protocol Selecting the Port 3-24 Specifying the Community Name(s) and Access Type(s) 3-25 3-26 Configuring SNMP Traps SNMP Traps Enabling SNMP Trap Messages 3-27 Selecting the Number of Trap Managers 3-28 Configuring a Destination for SNMP Traps n Setting the IP Address 000.000.000.000 3-29 Allocating Data Ports 3-30 3-31 Block or ACAMI Assignment Method 3-32 Individual Channel Assignment Method 3-33 Clearing DS0 Channel Allocation 3-34 Selecting the Timing Source Configuring for Network Timing 3-35 Establishing Access Security on the COM Port Setting a Password 3-36 Setting a Password Establishing Access Security on the COM Port 3-37 Entering a Password to Gain Access Setting a Password 3-38 Acquiring/Releasing the User Interface Acquiring the Active User Interface 3-39 Releasing the Active User Interface 3-40 Resetting the DSU/CSU 4-1 Monitoring and Testing 4 Installation Self-Test Health 4-2 4-3 Device Health and Status 4-4 Table 4-2. Device Health and Status Messages Message Description xxxxxxxx . Performance Reports 4-6 xx,xxx 4-7 ES= User Intvl: xxx Table 4-3. Performance Registers (1 of 3) Register Interval Description Totals Description 4-8 Table 4-3. Performance Registers (2 of 3) Register Totals DescriptionInterval Description 4-9 Table 4-3. Performance Registers (3 of 3) Register Totals DescriptionInterval Description 4-10 Resetting Performance Registers 4-11 Alarms 4-12 SNMP Traps SDCP Operation Configuring SNMP Traps 4-13 4-14 Troubleshooting 4-15 Test Jacks Test Commands 4-16 Remote Loopback Tests 4-17 Sending a Line Loopback Up or Down 4-18 Sending a V.54/ANSI FT1 Activation/Deactivation 4-19 Local Loopback Tests 4-20 Starting a Line Loopback CSUDSU 4-21 Starting a Payload Loopback 4-22 Starting a Repeater Loopback 4-23 Starting a Data Channel Loopback CSUDSU 4-24 Starting a Data Terminal Loopback 4-25 Aborting Loopbacks 4-26 Test Patterns Sending Test Patterns 4-27 Name Name and Dest Monitoring Test Patterns 4-28 Name Aborting Test Patterns 4-29 Send or Mon 4-30 Lamp Test Starting a Lamp Test 4-31 Aborting a Lamp Test Starting a Lamp Test 4-32 Displaying DSU/CSU Test Status A-1 SDCP Menu A * Page B-1 Technical Specifications B COMSPHERE 3000 Series Carrier Installation Manual . Table B-1. ACCULINK Model 3166 DSU/CSU Technical Specifications (1 of 2) Specifications Criteria Technical Specifications B-2 Table B-1. ACCULINK Model 3166 DSU/CSU Technical Specifications (2 of 2) Specifications Criteria C-1 Configuration Options C C-2 Port Configuration Options Table C-1. Port Configuration Options (1 of 5) C-3 Table C-1. Port Configuration Options (2 of 5) C-4 Table C-1. Port Configuration Options (3 of 5) C-5 Table C-1. Port Configuration Options (4 of 5) C-6 Table C-1. Port Configuration Options (5 of 5) C-7 Network Interface Configuration Options Table C-2. Network Interface Configuration Options (1 of 3) C-8 Table C-2. Network Interface Configuration Options (2 of 3) C-9 Table C-2. Network Interface Configuration Options (3 of 3) General Configuration Options Table C-3. General Configuration Options (1 of 2) C-10 Table C-3. General Configuration Options (2 of 2) User Interface Configuration Options Table C-4. User Interface Configuration Options (1 of 6) C-11 Table C-4. User Interface Configuration Options (2 of 6) C-12 Table C-4. User Interface Configuration Options (3 of 6) X.X C-13 Table C-4. User Interface Configuration Options (4 of 6) C-14 Table C-4. User Interface Configuration Options (5 of 6) C-15 C-16 Alarm Configuration Options Table C-5. Alarm Configuration Options (1 of 3) C-17 Table C-5. Alarm Configuration Options (2 of 3) C-18 Table C-5. Alarm Configuration Options (3 of 3) C-19 Management Configuration Options C-20 Table C-6. General Management Configuration Options (2 of 4) C-21 Table C-6. General Management Configuration Options (3 of 4) C-22 Table C-6. General Management Configuration Options (4 of 4) C-23 Table C-7. Management Trap Configuration Options (1 of 2) C-24 Table C-7. Management Trap Configuration Options (2 of 2) D-1 Pin Assignments D Equipment List T1 Network Interface Page D-3 EIA-530-A Port Interface Connector Number Direction Pin D-4 EIA-530-A-to-RS449 Cable Interface Figure D-3. EIA-530-A-to-RS449 Cable The EIA-530-A-to-RS449 adapter cable (Figure D-3) provides the RS449 interface shown in Table D-3. D-5 Table D-3. RS449 Cable Interface Signal Circuit Mnemonic CCITT Number Direction Pin D-6 EIA-530-A-to-V.35 Cable Interface Figure D-4. EIA-530-A-to-V.35 Cable The EIA-530-A-to-V.35 adapter cable (Figure D-4) provides the V.35 interface shown in Table D-4. D-7 Table D-4. V.35 Cable Interface Signal CCITT Number Direction Pin D-8 EIA-530-A-to-X.21 Cable Interface The EIA-530-A-to-X.21 adapter cable (Figure D-5) provides the X.21 interface shown in Table D-5. D-9 COM Port Interface Page D-11 COM Port to Modem Cable Figure D-8. Com Port to Modem Cable Page E-1 SNMP MIB Objects E E-2 MIB II (RFC 1213) ssssssss zzzz-zzz yy.yy.yy zzzz-zzz Interface Group, MIB II E-4 E-5 E-6 IP Group, MIB II E-7 E-8 E-9 ICMP Group, MIB II TCP Group, MIB II UDP Group, MIB II E-10 Transmission Group, MIB II DS1/E1 MIB (RFC 1406) E-11 Near End Group, DS1/E1 MIB E-12 E-13 E-14 Far End Group, DS1/E1 MIB E-15 DS1 Fractional Group, DS1/E1 MIB RS-232-like MIB (RFC 1317) General Port Table, RS-232-like MIB E-16 Asynchronous Port Table, RS-232-like MIB E-17 Synchronous Port Table, RS-232-like MIB E-18 Input Signal Table, RS-232-like MIB Output Signal Table, RS-232-like MIB E-19 Generic-Interface MIB Extensions (RFC 1229) Generic Interface Test Table, Generic Interface MIB E-20 E-21 Enterprise MIB E-22 Correlation between Menu Commands and SNMP Objects values dsx1LossOfSignal dsx1LossOfFrame dsx1RcvFarEnd dsx1RcvAIS dsx1OtherFailure E-23 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (2 of 4) E-24 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (3 of 4) E-25 Page F-1 IP Networking Address Scenario F F-2 Scenario 1 F-3 Scenario 2 F-4 Scenario 3 IP Networking Address Scenario 3166-A2-GB20-10 November 1998 F-5 Scenario 4 Figure F-4. Local Carrier Connected to Remote Carriers an Alternative 135.19.6.1 . . . . 135.19.6.16 135.19.20.1 . . . . 135.19.20.16 135.19.1.1 . . . . 135.19.1.16 Scenario 5 G-1 Front Panel Emulation G Installing Front Panel Emulation Software G-2 G-3 Starting Front Panel Emulation G-4 Displaying LED Conditions H-1 Asynchronous Terminal Interface Operation H Changing Configuration Options Before Using the ATI Configuring the DSU/CSU for SNMP or Telnet Access Resetting the ATI Initiating an ATI Session Entering a Password to Gain Access IP Network Addressing Scenarios Ending an ATI Session Asynchronous Terminal Interface Operation Menu Organization Figure H-2. Menu Organization H-4 Using ATI Screens H-5 NOTES: H-6 Setting Customer Identification H-7 Displaying LED Conditions H-8 Changing Configuration Options Changing Configuration Options Displaying or Editing Configuration Options H-9 H-10 Saving Edit Changes H-11 Establishing Access Security on a Port Setting a Password H-12 Setting a Password Establishing Access Security on a Port H-13 Entering a Password to Gain Access If an invalid password is entered three consecutive times If the password is invalid If the password is valid Page I-1 Equipment List I Equipment Feature Number Page GL-1 Glossary GL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 GL-9 GL-10 IN-1 Index A B C IN-2 D E F IN-3 G I K L M O P Q R S T U