Manuals / Parker Hannifin / Computer Equipment / Personal Computer

Parker Hannifin PA Series Removing the PowerStation from an Enclosure, Opening the PowerStation

Models: PA Series

1 65

Download 65 pages 28.37 Kb

Page 43

Removing the PowerStation from an Enclosure

Chapter 4: Maintaining the PowerStation

Performing Internal Maintenance

Removing the PowerStation from an Enclosure

To remove the PowerStation from it’s enclosure, follow the steps below.

Explosion Hazard!

•Do not connect or disconnect cables unless the power has been switched off, or the area is known to be safe.

WARNING!

1Turn off the power to the unit.

2Disconnect the following cables:

•Power Input cable

•Ground cable

•any communication cables

•any keyboard and mouse cables

3Take off the clamps.

4Place the PowerStation face down on a static dissipative mat, in a location free from dirt and moisture and protected against static discharge.

Opening the PowerStation

Once you have removed the PowerStation from it’s enclosure, you can open it up. Follow the steps below.

1Remove the CompactFlash card from it’s slot by pressing the eject button on the side of the PowerStation, similiar to that shown below.

Figure 4-3: Eject Button

CompactFlash

Card

CompactFlash

Eject Button

2Press in the eject button to return it to it’s retracted position.

3Remove the backshell screws on the PA PowerStation.

PA PowerStation User Guide

4-6

Image 43

Parker Hannifin PA Series manual Removing the PowerStation from an Enclosure, Opening the PowerStation, 3 Eject Button

Contents

A3-06692-101 PowerStationPA Series User Guide May Parker Electromechanical 50 W. TechneCenter Drive, Milford, OhioCopyright and Trademark Notice Product Warranty InformationSupported Models Table of Contents 2 Installing the PowerStation3 Starting Your PowerStation 1 Introduction4 Maintaining the PowerStation Page PA PowerStation User Guide Using this ManualINTRODUCTION Downloading Applications and Projects Hardware VersionsPA PowerStation User Guide PA PowerStation User Guide Documentation LibraryDocumentation Standards Text ConventionsISO Symbols Customer Support ServicesPA PowerStation User Guide PA PowerStation User Guide Review Chapter 4, Maintaining the PowerStationProduct Technical Support Technical TrainingPA PowerStation User Guide Getting StartedPA PowerStation User Guide INSTALLING THE POWERSTATIONSelecting a Location Underwriters Laboratories ApprovalElectrical Guidelines Temperature and Humidity GuidelinesField Terminal Wiring Requirements Environmental GuidelinesPA PowerStation User Guide Points to consider when performing a site review areRadiated Emissions Guidelines Enclosure GuidelinesPA PowerStation User Guide PA PowerStation User Guide Class I, Division 2 GuidelinesCreating the Cutout Preparing for InstallationPA PowerStation User Guide Mounting the PA PowerStation Installing the PA PowerStationPA PowerStation User Guide 5 For 5” and 6” units Torque them down to 6 in/lbs PA PowerStation User GuideMounting the AC Power Supply Installing an Optional AC Power SupplyPreparing a Location for the AC Power Supply Prepare the Power Supply Mounting SurfacePA PowerStation User Guide Connecting the Power Supply to the WorkstationFigure 2-3 Power Connector and Positive/Negative Wires Power Connector Power Supply +/- WiresPA PowerStation User Guide STARTING YOUR POWERSTATIONPowerStation Connectors Serial PortsChapter 3 Starting Your PowerStation PA PowerStation User GuidePowerStation Connectors PA PowerStation User Guide Settings and Pinouts for COM1Figure 3-2 DIP Switch on 5”, 6”, 8” and 10” Units Figure 3-1 COM2 Dip Switch Settings for 5”, 6”, 8”, and 10” UnitsPA PowerStation User Guide Note Be careful not to connect any wires to unused connector pins Dip Switch Settings and Pinouts for COM2 on 15” UnitsPA PowerStation User Guide Figure 3-5 DIP Switch on 15” Units Figure 3-4 COM2 Dip Switch Settings for 15” UnitsPA PowerStation User Guide RS-485 Directional Control Transferring Files from a PC to the PA PowerStationPA PowerStation User Guide PA PowerStation User Guide Figure 3-7 Serial Transfer Cable DiagramTo Adjust the Mode Settings Connecting to a Serial PrinterConnecting a PS/2 Mouse on 5”, 6”, 8”, and 10” Units Connecting a USB Mouse on 15” UnitsPA PowerStation User Guide Figure 3-8 Serial Printer Cable DiagramEthernet Port To Print to a Port Configured for DownloadingPA PowerStation User Guide PA PowerStation User Guide Configuring the Ethernet InterfaceTable 3-5 NET Directory Files CompactFlashPA PowerStation User Guide Starting the PowerStationStarting the PowerStation Writing to the CompactFlash Card Using the CompactFlash CardReinstalling the PowerStation Utilities Restoring a CompactFlash CardReformating the CompactFlash Card Using the BIOS UtilityPA PowerStation User Guide Entering Setup Using the BIOS UtilityPA PowerStation User Guide PA PowerStation User Guide MAINTAINING THE POWERSTATIONCleaning the Touchscreen Maintaining the TouchscreenThe Brightness property is fixed and cannot be adjusted Adjusting the Contrast only available on 5”, 6”, and 8” STN unitsUsing the MachineShop Shell Calibration Utility Calibrating the TouchscreenPA PowerStation User Guide Contrast Adjustment StepsEjector Button Replacing the CompactFlashPA PowerStation User Guide Electrostatic Discharge ESD Precautions Performing Internal MaintenancePA PowerStation User Guide Figure 4-3 Eject Button Removing the PowerStation from an EnclosureOpening the PowerStation PA PowerStation User GuidePA PowerStation User Guide Closing the PowerStationPA PowerStation User Guide Replacing the FuseFigure 4-4 Fuse Location PA5 - PA10 on left, PA15 on right Optional Components AC Power SupplyPA PowerStation User Guide Specific Issue Resolving ProblemsTable 4-1 Troubleshooting Guide General ProblemPA PowerStation User Guide Resolving Problems when Starting UpThe LED Power indicator on the back of the unit does not light The startup halts with the Award System Info screen displayedPA PowerStation User Guide Resolving Problems with the TouchscreenA keyboard doesn’t work 5”, 6”, 8”, and 10” units only Resolving Problems after Start UpThe display appears to be blank or very dim A PS/2 mouse doesn’t work 5”, 6”, 8”, and 10” units onlyThe Ethernet port doesn’t work Accessing the PowerStation UtilitiesOrdering Replacement Components A USB keyboard or mouse doesn’t work 15” onlyIf you need additional storage capacity, you can PA PowerStation User GuidePA PowerStation User Guide POWERSTATION SPECIFICATIONS1 RS232/422/485 configurable Physical Specifications1 RS232/422/485 configurable 1 RS232PA PowerStation User Guide Display SpecificationsViewing Angle PA PowerStation User GuideAppendix A PowerStation Specifications Viewing AnglePA PowerStation User Guide Environmental SpecificationsPA PowerStation User Guide Electrical SpecificationsAppendix A PowerStation Specifications Testing SpecificationsTable A-10, shows the mechanical testing specifications PA PowerStation User GuideTable A-11 Chemical Resistance Chart Touchscreen Chemical Resistance Faceplate Chemical ResistancePA PowerStation User Guide PA PowerStation User Guide SYSTEM CONFIGURATION FILESPA PowerStation User Guide System Configuration FilesCONFIG.SYS File AUTOEXEC.BAT FileAppendix B System Configuration Files PA PowerStation User Guidemouse and creates a new MOUSE.INI file Appendix B System Configuration Files PA PowerStation User GuideSystem Configuration Files ECHO END PA PowerStation User GuideAppendix B System Configuration Files System Configuration Files