6

 

00598

1

1

“A”

“A”

01553

2

(1) Bottom edge of mower

(2) Lift link adjustment nut

(1) Unterkante des Mähwerks

(2) Hubstangen-Stellmutter

(1) Extrémités du carter de coupe

(2) Ecrou de réglage du bras de suspension arrière

(1) Parte inferior de la esquina de la segadora

(2) Tuerca de ajuste del várillaje de levantamiento

(1) Bordo inferiore del tagliaerba

(2) Dado di regolazione dell'articolazione di sollevamento

(1) Onderkant van de maaimachine

(2) Bijstelmoer

SIDE-TO-SIDE ADJUSTMENT

Raise mower to highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” should be the same or within 6mm (1/4") of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

SEITLICHE EINSTELLUNG

Das Mähwerk auf die höchste Position einstellen.

Auf beiden Seiten des Mähwerks in der Mitte den Abstand von der Unterkante des Mähwerks zum Boden messen. Der Abstand “A” sollte auf den beiden Seiten um höchstens 6 mm (1/4') voneinander abweichen.

Falls eine Einstellung notwendig sein sollte, die Einstel- lung nur auf einer Seite des Mähwerks vornehmen.

Um eine Seite des Mähwerks anzuheben, die Hubstangen- Stellmutter auf der jeweiligen Seite festziehen.

Um eine Seite des Mähwerks abzusenken, die Hubstangen -Stellmutter auf der jeweiligen Seite lösen.

HINWEIS: Drei volle Umdrehungen der Stellmutter verändern die Höhe des Mähwerks um etwa 3 mm (1/8").

Nach der Einstellung die Abstände erneut prüfen.

REGLAGE TRANSVERSAL

Relever le carter de coupe au maximum.

A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rapport au sol .

La distance (A) doit être la même des deux côtés à 6 mm près.

Si un réglage est nécessaire, ne l'effectuer que d'un seul côté en se référant à l'autre côté.

Abaisser ou soulever un côté du carter de coupe en ajustant la position de l'écrou de réglage de ce côté.

REMARQUE: A trois tours complets de l'écrou de réglage correspond une variation de la hauteur au-dessus du sol, du carter de coupe, de 0,3 cm.

Contrôler à nouveau la distance au sol après chaque opération de réglage.

ADJUSTE DE LADO A LADO

Levante la segadora a su posición más alta.

A media distancia de ambos lados de la segadora, mida la altura desde la parte inferior del extremo de la segadora al suelo. La distancia “A” debe ser la misma o dentro de 6mm (1/4") de la una a la otra.

Si el ajuste es necesario, haga el ajuste en un lado de la segadora solamente.

Levante un lado de la segadora por apretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

Baje un lado de la segadora por desapretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

NOTA: Cada tres vueltas completas de la tuerca de ajuste cambiará la altura de la segadora en aproximadamente (1/8").

Vuelva a revisar las medidas después del adjuste.

REGOLAZIONE FIANCO A FIANCO

Alzare il tagliaerba nella posizione più alta.

Sui punti centrali di entrabi i lati del tagliaerba, misurare l'altezza dal bordo inferiore del tagliaerba al suolo. La distanza “A” deve essere la stessa o diversa non più di circa 6mm (1/4 di pollice).

Se necessario, fare la regolazione su un solo lato del tagliaerba.

Per alzare un lato del tagliaerba, stringere il dado di regolazione dell'articolazione di sollevamento su quel lato.

Per abbassare un lato del tagliaerba, allentare il dado di regolazione dell'articolazione di sollevamento su quel lato.

NOTA: Tre giri completi del dado di regolazione cambiano l'altezza del tagliaerba di circa 3 mm (1/8 di pollice).

Dopo aver fatto la regolazione, ricontrollare le misurazioni.

LINKS/RECHTS BIJSTELLEN

Zet de maaimachine in de hoogste stand.

Meet vervolgens in het midden tussen beide zijkanten van de maaimachine de hoogte van de onderkant van de maaimachine tot de grond. Afstand “A” moet ofwel hetzelfde zijn, ofwel binnen 6 mm (1/4") van elkaar liggen.

Indien bijstellen nodig is, mag dit slechts aan één kant van de maaimachine gebeuren.

Draai de bijstelmoer vaster aan de kant van de maaima- chine die u hoger wilt instellen.

Draai de bijstelmoer looser aan de kant van de maaima- chine die u lager wilt instellen.

N.B.: Drei slagen van de bijstelmoer veranderen de hoogte ongeveer 3 mm (1/8").

Controleer na het bijstellen de hoogte opnieuw.

57

Page 57
Image 57
Partner Tech P11597 SIDE-TO-SIDE Adjustment, Seitliche Einstellung, Reglage Transversal, Adjuste DE Lado a Lado

P11597 specifications

The Partner Tech P11597 is an advanced point-of-sale (POS) terminal designed to streamline retail operations and enhance the customer experience. With its robust features and modern technologies, it serves as a powerful tool for businesses in various sectors, including retail, hospitality, and service industries.

One of the standout features of the P11597 is its high-performance processing capabilities, powered by an efficient processor that ensures fast transaction processing. This speed is crucial in busy environments where customer satisfaction is paramount. The terminal is equipped with a responsive touchscreen interface, facilitating intuitive navigation for both staff and customers. The display boasts high resolution and vivid colors, allowing for clear visibility in various lighting conditions.

The P11597 supports multiple payment options, including contactless, chip-and-PIN, and traditional magnetic stripe cards. This versatility not only accommodates a wide range of customer preferences but also improves transaction security, reducing the risk of fraud. Moreover, the device is equipped with advanced encryption and security features to safeguard sensitive customer data.

In terms of connectivity, the Partner Tech P11597 includes a variety of ports, such as USB, Ethernet, and serial connections, enabling seamless integration with existing systems and peripherals like barcode scanners, printers, and cash drawers. This flexibility allows businesses to expand their capabilities as needed.

Another key characteristic is its durability. The terminal is designed to withstand the rigors of daily use in a bustling retail environment. With a spill and dust-resistant design, it can endure accidental spills and maintain cleanliness, ensuring longevity and reliability.

Additionally, the P11597 is built with energy efficiency in mind. Its power-saving technologies contribute to reduced operational costs, making it an environmentally friendly choice for businesses.

Overall, the Partner Tech P11597 combines cutting-edge technology with user-friendly features, making it an ideal solution for businesses looking to enhance their POS capabilities. Its speed, security, and durability underline its reputation as a reliable choice for modern retail operations, catering effectively to the needs of both operators and customers alike.