Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4950-NCE Description, Power, VoIP Link, Ethernet Link, Ethernet Speed, 10/100

Models: 4950-NCE

1 65

Download 65 pages 16.69 Kb

Page 19

SmartNode 4950-NCE Getting Started Guide1 • General information

	Table 5. SN4950-NCE Front and Rear panel LEDs

LED	Description

Note	If an error occurs, all LEDs will flash once per second.
Power	When lit, indicates power is applied.

Run	When lit, the unit is in normal operation. Flashes once per second during
	boot (startup).
VoIP Link	• On indicates the gateway is registered to an H.323 gatekeeper/SIP server, or,
	in the case of direct routing, has at least one active VoIP connection.
	• Off indicates the unit is not configured or registered, or has no active direct-
	routed VoIP connection.
	• Flashing green indicates that the unit is attempting to register or has failed
	to register.

Ethernet Link	• On when the Ethernet connection on the corresponding port has a
	link indication.
Ethernet Speed	When the Ethernet Link LED is on, then:
10/100	• On when the Ethernet is connected to a 100Mb network.
	• On when the Ethernet is connected to a 100Mb network.
	• Off when the Ethernet is connected to a 10Mb network.

Ethernet Speed	• On when the Ethernet is connected to a 1000Mb network.
1000
Ethernet Activity	• Flashes when data is received or transmitted at the corresponding Ethernet port.

PRI Link/Status	• On = in frame, no errors
	• Flash = Error
	• Fast Flash = Signal detected but no frame synchronization or aquisition is in
	process
	• Slow Flash = Framing synchronized, Signaling not established
G.SHDSL ACT	• Flashes when data is received or transmitted
(Rear panel)	• Off = No activity
	• Off = No activity

G.SHDSL LINK	• On when the G.SHDSL connection on the corresponding port has a
(Rear panel)	link indication.
	• Off = No G.SHDSL connection

SmartNode 4950-NCE front panel

19

Image 19

Patton electronic 4950-NCE Description, Power, VoIP Link, Ethernet Link, Ethernet Speed, 10/100, 1000, Ethernet Activity

Contents

Sales Office +1 301 SmartNode 4950-NCE SeriesMulti-Port T1/E1/PRI VoIP Enterprise Gateway Router Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents SmartNode installation Table of ContentsSummary Table of Contents Table of Contents6 Contacting Patton for assistance G.SHDSL Basic ConfigurationSpecifications Table of ContentsF End user license agreement E SmartNode 4950-NCE factory configurationCabling Port pin-outsList of Figures List of Tables Audience About this guideStructure Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightsages are present within the device when the power cord is connected Safety when working with electricityConvention Typographical conventions used in this documentGeneral observations General conventionsChapter 1 General information Chapter contentsFigure 1. SmartNode 4950-NCE SmartNode 4950-NCE overviewSN4950-NCE model codes SN4951-NCE model codes SmartNode 4950-NCE rear panelLAN ETH 0/1 DC power inputReset WAN ETH 0/0SN4950/4E120V SmartNode 4950-NCE front panel1 General information SN4950/1E30VEthernet Link PowerDescription VoIP LinkChapter contents Chapter 2 Applications overviewIntroduction Application-Multi-service ISDN Internet telephony IADFigure 4. Internet telephony IAD application Chapter SmartNode installationChapter contents Network Diagram Planning the installationCreate a network diagram see section “Network information” on page Verify power source reliability see section “Power source” on pageSoftware tools Installing the gateway routerAC Power Mains Installing cablesConnecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the PRIConnect the cables in the following order 5. Verify that the green Power LED is lit see figure Connecting the power supplyChapter contents Initial configurationChapter Connecting the SmartNode to your laptop PC 1. Connecting the SmartNode to your laptop PCIntroduction Changing the WAN IP address 2. Configuring the desired IP addressFactory-default IP settings Login3. Connecting the SmartNode to the network 4. Loading the configuration optional Load a new application image SmartWare via TFTP BootloaderStart Bootloader Start-up with factory configurationDownload it after starting up SmartWare with the following command Step Load a new application image SmartWare via the serial linkCommand RedBoot load -r -v -mAdditional information Additional informationChapter contents Chapter 5 G.SHDSL Basic ConfigurationIntroduction Line SetupConfiguring PPPoE Figure 8. Configuring the G.SHDSL card for PPPoEConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Link State Troubleshooting DSL ConnectionsDiagnostics PPPoE accessChapter contents Chapter 6 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCompliance CompliancePSTN Regulatory A Compliance informationChapter contents Appendix B SpecificationsFax and modem support Voice processing signalling dependentVoice connectivity Data connectivityIP services Voice signallingVoice routing-session router Physical Power Consumption 16W Operating temperature 32-104F 0-40CManagement SystemDSL Connection G.SHDSL Daughter Card if applicableFactor SpecsSmartNode Model Identification of the SmartNode devices via SNMPSysObjectID Table 13. SmartNode Models and their Unique sysObjectID Continued Chapter contents Appendix C CablingIntroduction ConsoleNote See section “Console port” on page 59 for console port pin-outs Ethernet EthernetC Cabling E1 PRIFigure 12. Connecting an E1 PRI port to an NT1 Figure 13. E1 PRI port crossover cableC Cabling T1 PRIFigure 14. Connecting a T1 PRI port to an NT device Figure 15. T1 PRI crossover cableChapter contents Appendix D Port pin-outsNote N/C means no internal electrical connection Console portIntroduction EthernetSignal PRI portG.SHDSL port SignalChapter contents Appendix E SmartNode 4950-NCE factory configurationIntroduction IntroductionChapter contents Appendix F End user license agreement2. Title 5. WarrantyEnd User License Agreement 1. Definitions7. Other licenses 6. Termination