Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4950-NCE manual Additional information

Models: 4950-NCE

1 65

Page 35

SmartNode 4950-NCE Getting Started Guide4 • Initial configuration

Step	Command	Purpose

8	RedBoot> go	Starts the application image that was downloaded to the vola-
		tile memory (RAM).

Note This type of download takes about 25 minutes since it uses a serial link at only 9600 bps.

Additional information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting, refer to the SmartNode Series SmartWare Software Configuration Guide on the CD-ROM.

Additional information

Page 35

Image 35

Patton electronic 4950-NCE manual Additional information

Contents

Sales Office +1 301 SmartNode 4950-NCE SeriesMulti-Port T1/E1/PRI VoIP Enterprise Gateway Router Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents SmartNode installation Table of ContentsSummary Table of Contents Table of Contents6 Contacting Patton for assistance G.SHDSL Basic ConfigurationSpecifications Table of ContentsF End user license agreement E SmartNode 4950-NCE factory configurationCabling Port pin-outsList of Figures List of Tables Structure About this guideAudience Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightsages are present within the device when the power cord is connected Safety when working with electricityConvention Typographical conventions used in this documentGeneral observations General conventionsChapter 1 General information Chapter contentsFigure 1. SmartNode 4950-NCE SmartNode 4950-NCE overviewSN4950-NCE model codes SN4951-NCE model codes SmartNode 4950-NCE rear panelLAN ETH 0/1 DC power inputReset WAN ETH 0/0SN4950/4E120V SmartNode 4950-NCE front panel1 General information SN4950/1E30VEthernet Link PowerDescription VoIP LinkChapter contents Chapter 2 Applications overviewFigure 4. Internet telephony IAD application Application-Multi-service ISDN Internet telephony IADIntroduction Chapter contents SmartNode installationChapter Network Diagram Planning the installationCreate a network diagram see section “Network information” on page Verify power source reliability see section “Power source” on pageSoftware tools Installing the gateway routerAC Power Mains Installing cablesConnect the cables in the following order Connecting the PRIConnecting the 10/100/1000Base-T Ethernet LAN and WAN cables 5. Verify that the green Power LED is lit see figure Connecting the power supplyChapter Initial configurationChapter contents Introduction 1. Connecting the SmartNode to your laptop PCConnecting the SmartNode to your laptop PC Changing the WAN IP address 2. Configuring the desired IP addressFactory-default IP settings Login3. Connecting the SmartNode to the network 4. Loading the configuration optional Load a new application image SmartWare via TFTP BootloaderStart Bootloader Start-up with factory configurationDownload it after starting up SmartWare with the following command Step Load a new application image SmartWare via the serial linkCommand RedBoot load -r -v -mAdditional information Additional informationChapter contents Chapter 5 G.SHDSL Basic ConfigurationIntroduction Line SetupConfiguring PPPoE Figure 8. Configuring the G.SHDSL card for PPPoEConfiguration Summary Using PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Link State Troubleshooting DSL ConnectionsDiagnostics PPPoE accessChapter contents Chapter 6 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCompliance CompliancePSTN Regulatory A Compliance informationChapter contents Appendix B SpecificationsFax and modem support Voice processing signalling dependentVoice connectivity Data connectivityVoice routing-session router Voice signallingIP services Physical Power Consumption 16W Operating temperature 32-104F 0-40CManagement SystemDSL Connection G.SHDSL Daughter Card if applicableFactor SpecsSysObjectID Identification of the SmartNode devices via SNMPSmartNode Model Table 13. SmartNode Models and their Unique sysObjectID Continued Chapter contents Appendix C CablingNote See section “Console port” on page 59 for console port pin-outs ConsoleIntroduction Ethernet EthernetC Cabling E1 PRIFigure 12. Connecting an E1 PRI port to an NT1 Figure 13. E1 PRI port crossover cableC Cabling T1 PRIFigure 14. Connecting a T1 PRI port to an NT device Figure 15. T1 PRI crossover cableChapter contents Appendix D Port pin-outsNote N/C means no internal electrical connection Console portIntroduction EthernetSignal PRI portG.SHDSL port SignalChapter contents Appendix E SmartNode 4950-NCE factory configurationIntroduction IntroductionChapter contents Appendix F End user license agreement2. Title 5. WarrantyEnd User License Agreement 1. Definitions7. Other licenses 6. Termination