Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4950-NCE manual Line Setup, Configuring PPPoE, Introduction

Models: 4950-NCE

1 65

Download 65 pages 16.69 Kb

Page 37

Figure 8. Configuring the G.SHDSL card for PPPoE

SmartNode 4950-NCE Getting Started Guide	5 • G.SHDSL Basic Configuration

Introduction

The SN4950-NCE model has an option for a built-in G.SHDSL modem. The modem appears in the configu- ration as "port dsl 0 0" mode.

Profile

napt

WAN

port dsl 0\ 0\

	pvc
vpi 8	vci 35

pppoe

session MyISP

use
profile
WAN	napt

WAN

interface

bind subscriber
	MySubscriber
interface
bind	router
WAN

Subscriber PPP MySubscriber

CAUTION

context

ip

Figure 8. Configuring the G.SHDSL card for PPPoE

The Modem setup uses IP messages within its own subnet: 192.0.2.0/24. SmartNodes with built-in modems cannot use this subnet in any other way.

Note For information about the specifications of the G.SHDSL daughter card, see Appendix B, “Specifications” on page 46.

Line Setup

There is no line modulation setting. The modems automatically adapt to the bit rate and modulation used. The status LED on the back of the device is blinking while the modem attempts to connect and lit when the link is established. If the modem keeps blinking, check the cabling,

Configuring PPPoE

Figure 8 explains how to configure PPPoE on the SmartNode’s built-in G.SHDSL card. To configure the DSL port for PPPoE, first you need to log in to the SmartNode via the CLI and enter configuration mode.

login: administrator

password: <enter> SN4xxx>enable SN4xxx>#configure

Introduction

37

Image 37

Patton electronic 4950-NCE manual Line Setup, Configuring PPPoE, Introduction, Configuring the G.SHDSL card for PPPoE

Contents

Multi-Port T1/E1/PRI VoIP Enterprise Gateway Router SmartNode 4950-NCE SeriesGetting Started Guide Sales Office +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents SmartNode installationSpecifications G.SHDSL Basic ConfigurationTable of Contents 6 Contacting Patton for assistanceCabling E SmartNode 4950-NCE factory configurationPort pin-outs F End user license agreementList of Figures List of Tables Audience About this guideStructure impaired functioning PrecautionsNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injuryages are present within the device when the power cord is connected Safety when working with electricityGeneral observations Typographical conventions used in this documentGeneral conventions ConventionChapter 1 General information Chapter contentsFigure 1. SmartNode 4950-NCE SmartNode 4950-NCE overviewSN4950-NCE model codes SN4951-NCE model codes SmartNode 4950-NCE rear panelReset DC power inputWAN ETH 0/0 LAN ETH 0/11 General information SmartNode 4950-NCE front panelSN4950/1E30V SN4950/4E120VDescription PowerVoIP Link Ethernet LinkChapter contents Chapter 2 Applications overviewIntroduction Application-Multi-service ISDN Internet telephony IADFigure 4. Internet telephony IAD application Chapter SmartNode installationChapter contents Create a network diagram see section “Network information” on page Planning the installationVerify power source reliability see section “Power source” on page Network DiagramAC Power Mains Installing the gateway routerInstalling cables Software toolsConnecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the PRIConnect the cables in the following order 5. Verify that the green Power LED is lit see figure Connecting the power supplyChapter contents Initial configurationChapter Connecting the SmartNode to your laptop PC 1. Connecting the SmartNode to your laptop PCIntroduction Factory-default IP settings 2. Configuring the desired IP addressLogin Changing the WAN IP address3. Connecting the SmartNode to the network 4. Loading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Load a new application image SmartWare via TFTPDownload it after starting up SmartWare with the following command Command Load a new application image SmartWare via the serial linkRedBoot load -r -v -m StepAdditional information Additional informationChapter contents Chapter 5 G.SHDSL Basic ConfigurationConfiguring PPPoE Line SetupFigure 8. Configuring the G.SHDSL card for PPPoE IntroductionConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Diagnostics Troubleshooting DSL ConnectionsPPPoE access Link StateChapter contents Chapter 6 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationPSTN Regulatory ComplianceA Compliance information ComplianceChapter contents Appendix B SpecificationsVoice connectivity Voice processing signalling dependentData connectivity Fax and modem supportIP services Voice signallingVoice routing-session router Management Power Consumption 16W Operating temperature 32-104F 0-40CSystem PhysicalFactor G.SHDSL Daughter Card if applicableSpecs DSL ConnectionSmartNode Model Identification of the SmartNode devices via SNMPSysObjectID Table 13. SmartNode Models and their Unique sysObjectID Continued Chapter contents Appendix C CablingIntroduction ConsoleNote See section “Console port” on page 59 for console port pin-outs Ethernet EthernetFigure 12. Connecting an E1 PRI port to an NT1 E1 PRIFigure 13. E1 PRI port crossover cable C CablingFigure 14. Connecting a T1 PRI port to an NT device T1 PRIFigure 15. T1 PRI crossover cable C CablingChapter contents Appendix D Port pin-outsIntroduction Console portEthernet Note N/C means no internal electrical connectionG.SHDSL port PRI portSignal SignalChapter contents Appendix E SmartNode 4950-NCE factory configurationIntroduction IntroductionChapter contents Appendix F End user license agreementEnd User License Agreement 5. Warranty1. Definitions 2. Title7. Other licenses 6. Termination