Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4950-NCE manual Summary Table of Contents, List of Figures, List of Tables

Models: 4950-NCE

1 65

Download 65 pages 16.69 Kb

Page 4

Table of Contents

Table of Contents
	Summary Table of Contents	3
	Table of Contents	4
	List of Figures	7
	List of Tables	8
	About this guide	9
	Audience	9
	Structure	9
	Precautions	10
	Safety when working with electricity	11
	General observations	12
	Typographical conventions used in this document	12
	General conventions	12
1	General information	13
	SmartNode 4950-NCE overview	14
	SN4950-NCE model codes	15
	SN4951-NCE model codes	16
	SmartNode 4950-NCE rear panel	16
	SmartNode 4950-NCE front panel	18
2	Applications overview	20
	Introduction	21
	Application—Multi-service ISDN Internet telephony IAD	21
3	SmartNode installation	22
	Planning the installation	23
	Site log	23
	Network information	23
	Network Diagram	23
	IP related information	23
	Software tools	24
	AC Power Mains	24
	Location and mounting requirements	24
	Installing the gateway router	24
	Placing the SmartNode	24
	Installing cables	24
	Connecting the PRI	25
	Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables	25
	Installing the DSL WAN cable	25
	Connecting the power supply	26
4	Initial configuration	27
	Introduction	28

4

Image 4

Patton electronic 4950-NCE manual Summary Table of Contents, List of Figures, List of Tables, About this guide

Contents

SmartNode 4950-NCE Series Multi-Port T1/E1/PRI VoIP Enterprise Gateway RouterGetting Started Guide Sales Office +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Summary Table of ContentsTable of Contents SmartNode installationG.SHDSL Basic Configuration SpecificationsTable of Contents 6 Contacting Patton for assistanceE SmartNode 4950-NCE factory configuration CablingPort pin-outs F End user license agreementList of Figures List of Tables Audience About this guideStructure Precautions impaired functioningNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injurySafety when working with electricity ages are present within the device when the power cord is connectedTypographical conventions used in this document General observationsGeneral conventions ConventionChapter contents Chapter 1 General informationSmartNode 4950-NCE overview Figure 1. SmartNode 4950-NCESN4950-NCE model codes SmartNode 4950-NCE rear panel SN4951-NCE model codesDC power input ResetWAN ETH 0/0 LAN ETH 0/1SmartNode 4950-NCE front panel 1 General informationSN4950/1E30V SN4950/4E120VPower DescriptionVoIP Link Ethernet LinkChapter 2 Applications overview Chapter contentsIntroduction Application-Multi-service ISDN Internet telephony IADFigure 4. Internet telephony IAD application Chapter SmartNode installationChapter contents Planning the installation Create a network diagram see section “Network information” on pageVerify power source reliability see section “Power source” on page Network DiagramInstalling the gateway router AC Power MainsInstalling cables Software toolsConnecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the PRIConnect the cables in the following order Connecting the power supply 5. Verify that the green Power LED is lit see figureChapter contents Initial configurationChapter Connecting the SmartNode to your laptop PC 1. Connecting the SmartNode to your laptop PCIntroduction 2. Configuring the desired IP address Factory-default IP settingsLogin Changing the WAN IP address3. Connecting the SmartNode to the network 4. Loading the configuration optional Bootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TFTPDownload it after starting up SmartWare with the following command Load a new application image SmartWare via the serial link CommandRedBoot load -r -v -m StepAdditional information Additional informationChapter 5 G.SHDSL Basic Configuration Chapter contentsLine Setup Configuring PPPoEFigure 8. Configuring the G.SHDSL card for PPPoE IntroductionConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Troubleshooting DSL Connections DiagnosticsPPPoE access Link StateChapter 6 Contacting Patton for assistance Chapter contentsWarranty Service and Returned Merchandise Authorizations RMAs Warranty coverageContact information Patton support headquarters in the USAOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix A Compliance information Chapter contentsCompliance PSTN RegulatoryA Compliance information ComplianceAppendix B Specifications Chapter contentsVoice processing signalling dependent Voice connectivityData connectivity Fax and modem supportIP services Voice signallingVoice routing-session router Power Consumption 16W Operating temperature 32-104F 0-40C ManagementSystem PhysicalG.SHDSL Daughter Card if applicable FactorSpecs DSL ConnectionSmartNode Model Identification of the SmartNode devices via SNMPSysObjectID Table 13. SmartNode Models and their Unique sysObjectID Continued Appendix C Cabling Chapter contentsIntroduction ConsoleNote See section “Console port” on page 59 for console port pin-outs Ethernet EthernetE1 PRI Figure 12. Connecting an E1 PRI port to an NT1Figure 13. E1 PRI port crossover cable C CablingT1 PRI Figure 14. Connecting a T1 PRI port to an NT deviceFigure 15. T1 PRI crossover cable C CablingAppendix D Port pin-outs Chapter contentsConsole port IntroductionEthernet Note N/C means no internal electrical connectionPRI port G.SHDSL portSignal SignalAppendix E SmartNode 4950-NCE factory configuration Chapter contentsIntroduction IntroductionAppendix F End user license agreement Chapter contents5. Warranty End User License Agreement1. Definitions 2. Title6. Termination 7. Other licenses