If,contrary to expectation, you have any problems using this
TV-VIDEOCombi, it may be caused by one of the reasons
mentionedbelow. You can also call the customer service
centreinyour country.
Youwill find the phone number in the enclosed guarantee
leaflet.Have the model number (MODEL NO) and the
productionnumber (PROD.NO) of your video recorderready.
Technicalproblem:
•Youcan reset the settings on your set (careful: all information will
bedeleted): with the video recorder switched on, hold the
Handthe Ibuttonuntil the screen switches off.
YourTV-VIDEO Combi does not respond to any button being
pressed:
•Thereis no power supply: check the power supply
•Aprogrammed recording is currently being made: to cancel the
programmedrecording. press STANDBYmforseveral seconds.
•Parentalcontrol is on: switch the parental control off.
•Continuousplayback is on: switch the continuous playback off.
•Thereis a technical problem: switch off with the 8power
switchfor 30 seconds, then switch it on again.
Cassetteis jammed in the TV-VIDEO Combi:
•Don’tuse force. Switch off with the 8powerswitch for 30
seconds,then switch it on again.
Remotecontrol does not work:
•Remotecontrol not pointed toward the TV-VIDEO Combi: point it
atthe TV-VIDEO Combi.
•Batterieshave run out: change the batteries.
•Youhave given the wrong remote control command: read
’Switchingremote control command’ in chapter ’Additional
functions’.
Nopicture when you play a cassette:
•Thereis no recording on the cassette: change the cassette.
Poorpicture quality when you play a cassette:
•Thecassette badly worn or of poor quality: use new cassette.
•Trackingis not properly adjusted or the video heads are dirty:
turnto chapter ’PLAYBACK FUNCTIONS’ and read the section
’Cleaningthe video heads’.
•Readthe section ’Picture interference’.
•Youare playing a cassette with a LongPlay recording on it:
Excellentpicture quality is only guarateed with recordings made
inStandardPlay recording speed.
TheTV-VIDEO Combi will not record:
•TheTV channel you want to record is not stored or you selected
thewrong programme number: check TV channels stored.
•Youhave loaded a cassette which cannot be recorded on: undo
theerase protection on the cassette.
Programmedrecording does not work:
•Youhave not set the TIMER properly: check the TIMER blocks.
•Youhave programmed the wrong time or date: check time and
date.
•Youhave put in a cassette that cannot be recorded on: undo the
eraseprotection on the cassette.
•’PDC’or ’VPS’ switched on but ’PDC/VPS time’ wrong: enter PDC
orVPS time exactly to the minute. Have the aerialchecked.
Recordingstarts as soon as the satellite receiver or second
videorecorder is switched on:
•Externallycontrolled recording switched on: Switch off the
externallycontrolled recording.
’SmartClock’ setting does not work:
•Youhave stored a TV channel on programme number ’P01’ that
doesnot transmit TELETEXT: On ’P01’ store a TVchannel that
transmitsTELETEXT.
•PoorTELETEXT reception: On ’P01’ store a TV channel with
goodTELETEXT reception.
•Youhave not activated the Smart Clock function: Switch the
function’ON’.
Youhear a very short and soft noise coming fromyour
TV-VIDEOCombi at 3:00 at night:
•’SmartClock’ is checking the time: Switch off the Smart Clock
function.
TELETEXTdoes not start at page 100:
•Youhave stored a different preferred page: Store page 100 as
preferredpage.
9. Before you call an engineer25