Philips 220X manual VGA switchers

INSTALLATION ACCESSORIES

VGA switchers

All selectors offered below transfer the VGA signal from 2 up to 8 connected computers to a monitor or projector.

VGA share Basic 2 : 1 No. 5816-11

￿2 inputs / 1 output (all HD15 f)

￿2 select buttons

￿Auto skip, for skipping non-active inputs

￿4 status LEDs

￿Frequency 250 MHz

￿Supports 1920x1440 pixels and DDC1, DDC2, DDC2B, DDC2B+, DDC2AB

￿Metal casing 128x75x45 mm

￿Power supply DC 9V, 300mA

VGA share Basic 4 : 1 No. 5816-12

similar to 5816-11 but with

￿4 inputs / 1 output (all HD15 f)

￿4 select buttons

￿8 status LEDs

VGA share Basic 8 : 1 No. 5816-3

￿8 inputs (HD15 m) / 1 output (HD 15 f)

￿IR remote control for selection of sources

￿Buttons on the unit: up/down for successive selection and blank

￿16 status LEDs

￿Supports 2048x1536 pixels @ 60 Hz and DDC, DDC2, DDC2B

￿Plastic casing 170x190x45 mm

￿Power supply AC9V, 4.5 W and 1.2 m VGA cable (m / f)

VGA Audio Share Pro 2 : 1 - automatic No. 5816-4

Switches automatically to second input in case of a loss of the original input signal.

￿2 VGA inputs / 2 outputs (HD15 f)

￿2 Audio inputs / 1 output (3.5 mm jack / f)

￿Loop input = input 1

￿ID-Bit control

￿Frequency VGA 300 MHz, Audio 100 kHz

￿Control: automatic or via contact switch

￿Metal casing 120x75x25 mm

￿Power supply 12 V DC, 50 mA

VGA Audio Share Pro 3 : 2 No. 5816-6

High-quality switcher for VGA and symmetric audio signals. Transforms 3 inputs into 2 identical outputs.

￿3 VGA inputs / 2 outputs (HD 15 f)

￿3 Stereo audio inputs / 2 outputs (5-pin clamp connection)

￿Frequency VGA 450 MHz, Audio > 100 kHz

￿Control: 3 select buttons, relais inputs

￿Metal casing 220x180x45 mm

￿Power supply 12 V DC, 146 mA

￿Optional 19" rack adapter

VGA Matrix 2x2 No. 5816-5

The VGA Matrix connects 2 computers to 2 displays or projectors and also functions as signal amplifier.

Each output shows either input 1, input 2 or no signal

￿2 selectable VGA inputs / 2 outputs (all HD15 f)

￿2 select buttons

￿4 status LEDs

￿Frequency 250 MHz

￿Supports 1920x1440 pixels @ 60 Hz

￿Metal casing 130x75x42 mm

￿Power supply DC 7.5 V, 800 mA

Presentation switcher N	No. 7485-2
Presentation switcher RC	No. 7485-3

￿The „central control unit“ for the smaller or medium-sized conference rooms

￿Combines 4 switchers in a 2HE 19" casing

￿4 : 1 switcher for VGA with Audio, Video with Audio, S-Video with Audio

￿All Audio connections symmetric with clamps

￿XLR microphone connection can be adapted to dynamic or condensor microphones

￿Talk-over function for microphone and volume control for Audio source

￿Integrated Audio amplifier 2 x 5 W RMS - for smaller conference rooms a separate amplifier is not necessary

￿Inputs:

4 VGA (HD15 f), 4 S-Video (4 pin-Mini-Din / f), 4 Video (BNC), 12 Audio (symmetric), 1 microphone (XLR)

￿Outputs:

1 VGA (HD 15 f), 1 S-Video (4 pin-Mini-Din / f), 1 Video (BNC), 3 Audio (symmetric), 1 Master Audio (symmetric)

Parallel/additional VGA output via Cat5/Twisted Pair - for transmission of VGA signals via Cat5-UTP cable up to 100 m (optional receiver module required)

￿Operation:

Via buttons on unit, RS 232-/485-/network interface or IR remote control

￿Control for Audio and microphone level

￿Frequency 350 MHz (VGA), S-Video (385 MHz), Video / SDI (650 MHz)

Additional functions of presentation switcher RC:

￿Integrated Room Controller for controlling the projector, other signal sources, screens, lifts or technical devices in the house e.g. light, shades etc.

￿2 bi-direct RS 232 interfaces

￿3 infrared (for each 2 diodes)

￿4 relais

￿1 Ethernet port

￿Easy programming via Windows-based software resp. integrated IR learning module

CAT5-VGA receiver for 7485-2/-3 No. 7481-10

￿1 input / 1 output (1 x RJ 45 / f, HD15 / f)

￿Frequency 15 MHz @ - 3 dB

￿Control for level (gain) & EQ (Peaking)

￿Metal casing 60 x 65 x 25 mm

￿Power supply DC 12 V, 30mA

Subject to technical alterations, as well as to changes of the design and the colour 35