Philips 51PW9303 manual Connecting a VCR, Vol

Connecting Accessory Devices to Your TV

CONNECTING A VCR

The TV’s audio/video (AV) input jacks provide for direct picture and sound connections

between the TV and accessory devices such as VCRs, DVD players, and others that have AV out- put jacks.

This example, which uses the INPUT-AV 1 jacks, shows you one way you can connect a VCR to your TV.

Refer to the directions-for-use manual for your VCR for further information on connections.

To make the connections shown in this example, you will need:

•one coaxial cable (75Ω )

•one cable for a video connection (standard RCA-type phono plug)

•two cables for audio connections (standard RCA-type phono plugs) (only one cable is needed for a nonstereo VCR).

NOTE: The cables are not supplied with your TV. You should be able to buy them at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039

				Rear of TV	HD INPUT-AV 5
					DVI
2	3				HD INPUT-AV 4
				4 INPUT-AV 2	R/Pr
					G/Y
	ANTENNA IN 75Ω	INPUT-AV 1	Y		B/Pb
		VIDEO		VIDEO
	S-VIDEO			S-VIDEO
			Pb	L
		L			V
						L	Coaxial Cable
		L		L	L
					SYNC
		AUDIO		AUDIO	H	AUDIO	Lead-in from
			Pr		AUDIO		Cable TV Company
		R		R	R	R
							or VHF/UHF Antenna
Rear of VCR*						1
						AUDIO
						L	ANT
							IN
							IN
						R
						VIDEO
							OUT
						OUT	IN CH3 CH4

*(Example: Philips VCR model VR674CAT)

AV1

1 Connect a cable TV or antenna signal to the ANT IN jack on the back of the VCR.

2 Connect from the OUT jack on the back of the VCR to the ANTENNA IN 75Ω jack on the back of the TV.

3 Connect the VIDEO OUT jack on the back of the VCR to the INPUT-AV 2 VIDEO jack on the back of the TV.

4 Connect the audio output R(ight) and L(eft) jacks on the back of the VCR to the INPUT-AV 2 AUDIO jacks on the back of the TV.

NOTE: If the VCR is a mono (nonstereo) unit, connect only the left audio cable, which usually has a white-coded plug.

5 Press the AV button on the remote con- trol as many times as necessary to select the AV2 source for viewing of materials from the VCR.

POWER

TV	VCR	ACC
		ACTIVE
SWAP	PIP CH	CONTROL FREEZE
DN	UP
SOUND		PICTURE
STATUS/		MENU/
EXIT		SELECT
	MUTE
VOL		CH

1		2	3
4		5	6
7		8	9
TV/VCR		0
A/CH			SURF
5	SURF	PIP ON/OFF
	REC • FORMAT SLEEP
	SAP
AV		DOLBY V	PROG.LIST
ITR/	HOME	HOME	PERSONAL
RECORD	VIDEO	MOVIES
POSITION			PIP

HELPFUL HINTS

•Stereo sound will pass from the ANT

OUT jack on the VCR to the ANTENNA IN 75Ω jack on the TV only when the VCR is in TV mode. This is the mode that allows the TV to use its channel selector.

•To simplify making connections, audio and video cables often have color-coded plugs. The jacks on your TV are likewise color coded to match the plugs. The cod- ing is as follows:

—Yellow for video (composite) —Red for the right audio channel —White for the left audio channel

NOTE: If your VCR is mono (non- stereo), you will connect only one audio cable. You must ensure that the TV is set to MONO for the signal source to which you’ve connected the VCR (INPUT-AV 2, INPUT-AV 1, or the side panel inputs [AV3]). Otherwise, you will receive sound from only one of the TV’s speakers. See page 36.

cCHECK IT OUT

You can display the AV1, AV2, or AV3 signal sources in the PIP window. See page 7 of the Quick Use and Setup Guide for information on using the Picture-in-Picture (PIP) feature.

9