Philips 55PW9383 Connecting AN HD Receiver to the HD INPUT-AV 4 Jacks, Connect coaxial cables

Connecting Accessory Devices to Your TV

CONNECTING AN HD RECEIVER TO THE HD INPUT-AV 4 JACKS

Digital equipment with a 1080i or 480p out- put, is compatible with the HD INPUT-AV 4

video jacks.

NOTE: This television is designed to be compati- ble with high-definition signal standards 1080i and 480p as specified by the Electronic Industries Association standard EIA770.3. Because output standards may vary by manufacturer, you may encounter some digital equipment that will not properly display pictures on the TV.

To make the connections shown in this example, you will need:

•one S-VIDEO cable

•three cables for video connections (standard RCA connectors)

•four cables for audio connections (standard RCA connectors)

•one coaxial cable (75Ω).

NOTE: The cables are not supplied with your TV. You should be able to buy them at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039.

1 Connect S-VIDEO and audio cables. NOTE: This example uses

INPUT-AV 1. You can use INPUT-AV 2 or the side input jacks if you want.

•Connect an S-VIDEO cable from the HD receiver’s S-VIDEO jack to the TV’s INPUT-AV 1 S-VIDEO jack.

•Connect from the HD receiver’s AUDIO L(eft) and R(ight) jacks to the TV’s INPUT-AV 1 L(eft) and R(ight) AUDIO jacks.

2 Connect component video and audio

cables to the TV’s HD inputs.

•Connect from the YPRPB jacks on the HD receiver to the TV’s HD INPUT-AV 4 G/Y, R/Pr, B/Pb jacks.

•Connect from the HD receiver’s AUDIO L(eft) and R(ight) jacks to the TV’s HD INPUT-AV 4 L(eft) and R(ight) AUDIO jacks.

3	Connect coaxial cables.
	• Connect the coaxial cable lead-in from
	your cable outlet, cable converter box, or

VHF/UHF antenna to the IN FROM ANT jack on the HD receiver.

• Connect a coaxial cable from the OUT TO TV jack to the ANTENNA IN 75Ω jack on the TV.

• Connect the coaxial cable lead-in from a satellite dish antenna to the SATELLITE IN jack on the HD receiver.

4 Refer to the directions-for-use manual that came with the HD receiver for setup instructions.

3

ANTENNA IN 75Ω

Rear of TV

HD INPUT-AV 5

DVI

2

HD INPUT-AV 4

G/Y

INPUT-AV 1

1

INPUT-AV 2

SUBWOOFER

R/Pr

2

1

Y

B/Pb

VIDEO

VIDEO

SL-VIDEO L

VIDEO

L

S- L

V L

L

Coaxial Cable

SYNC

AUDIO

Pr

AUDIO

H

AUDIO

Lead-in

R

R

R

R

from

Satellite

Dish Antenna

UDIO

AUDIO

Y

L

L

VCR

OUT TO TV

CONTROL

CH 3

PB

R

R

CH 4

DIGITAL

RF

PR

AUDIO OUT

PHONE JACK REMOTE

VIDEO

VIDEO

S-VIDEO

IN FROM ANT

SATELLITE IN

Rear of HD Receiver

Coaxial Cable Lead-in

3

3

(Example: Philips DSHD800)

from Cable Outlet,

Cable Converter Box,

or VHF/UHF Antenna

HELPFUL HINTS

•HD receivers will supply stereo sound to the TV only through the audio left and right cables, not through the coaxial cable.

•Making a standard connection along with the HD connection as shown in the example (S-VIDEO) on this page will allow you to see the receiv- er’s on-screen menu and a picture (valid signal) from the receiver should it be switched to SD mode.

•The HD INPUT-AV 4 jacks are for standard RCA-type phono plugs. Your HD receiver may use RCA or BNC output jacks. If your HD receiver comes with BNC jacks, you will need to purchase BNC-to-RCA adapters to connect the receiver to the TV. You should be able to pur- chase these adapters at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039.

			OR
BNC-to-	BNC	Adapter	RCA
RCA	Connector	Fitted to	Connector
Adapter		Connection

•The HD INPUT-AV 4 jacks are compatible with some digital equipment having RGB outputs with “sync on green” or RGB with “separate H and V sync.” Output standards for digital equipment, however, may vary by manu- facturer. No industry standards have been established for HD television RGB signal systems, timing, synchronization, and signal strengths. If the digital equipment you want to connect to your TV offers both component video and RGB outputs, component video is the suggested connection to use.

•The default color-space setting for the HD INPUT-AV 4 jacks is YPbPr. RGB is also an option. If the picture color looks grossly incorrect, try changing either the receiver’s or TV’s color space. See the receiver’s directions-for-use manual for information on setting its color space. Or see page 61 in this manual for setting the TV’s AV4 color space.

•AV4 and AV5 do not function with the PIP feature. They cannot be dis- played in the PIP window, nor can the PIP window be displayed when those signal sources are being viewed on the main screen.

15