Manuals / Philips / TV and Video / Projection Television

Philips 9P5031C1, 9P5531C1, 9P6031C1, 9P5034C1, 9P5534C1, 9P6034C1 manual Search Method

Models: 9P5031C1, 9P5531C1, 9P6031C1, 9P5034C1, 9P5534C1, 9P6034C1

1 52

Download 52 pages 61.59 Kb

Page 36

SETTING THE REMOTE TO WORK OTHER DEVICES - SEARCH

SEARCH METHOD

Your TV remote can be set to work various accessory

SATELLITE RECEIVER

devices (VCRs, Cable Converters, Satellite Receivers) by what is called the SEARCH method.

Note: The Search Method only works with devices equipped with

Channel Display Indicators or capability. If the "Direct Access" code number method (shown in the previous section) did not set your remote to work your acces- sory device, then follow the easy steps listed below.

BEGIN

1Turn ON the desired device. Press the correct VCR or ACC system button on the remote.

2 Stand at least six feet away

from the front of the accessory

device. Point the remote toward

the unit. HOLD DOWN the

SURF and the desired System

(VCR or ACC) buttons at the

same time. KEEP HOLDING

1

VCR

			06
			07
	CABLE TV		08
	CABLE TV	07	09
	CONVERTER	07	09
	CONVERTER	06
	06	0809
		070809
	Don't let the Accessory Device
	scan up more than five channels
	(in Search mode).		Six Feet
			Six Feet
			(minimum)

3

BUTTONS DOWN.

3Watch the Channel Indicator on the unit. Channel Numbers will SCAN UP when the unit has been identified. This may take up to two minutes.

4Release the SURF and System (VCR or ACC) buttons as soon as channel numbers start to scan up. The code has been identified and the remote is ready to operate with the accessory device.

STOP

SMART HELP

Remember, a minute or two

can seem very long, but the code should be located within two minutes.

Don't let the accessory device scan up more than five channels. The remote may pass up the right code and another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work with the desired unit.

REC ●		PLAY ▶		STATUS
CLEAR
REW		MENU
REW	−	M	+	FF
◀◀	−	M	+	FF
				▶▶
				PAUSE II
MUTE		STOP	■	SURF
VOL				CH	2
ON/OFF		POS	SWAP	FREEZE	2	4
				SIZE
100+		1	2	3
TV/VCR		4	5	6
ENTER		7	8	9
SLEEP		7	8	9
SMART			0
POWER		VCR	ACC	TV
		M	O D	E

2 4

36

Image 36

Philips 9P5031C1, 9P5531C1, 9P6031C1, 9P5034C1, 9P5534C1, 9P6034C1 manual Setting the Remote to Work Other Devices Search

Contents

Projection Television Warranty Owner Confirmation Safety Instructions Read before operating equipment Table of Contents Features End-of-Life disposalPicture Menu Control Adjustments COLOR, Brightness SHARPNESS, TINT, PicturePicture Menu Controls Flesh CorrectionRED/BLUE Convergence Select Convergence con- trolRemember. Convergence Picture Source Select Picture SourcePress the Menu buttons Feature Menu Controls Closed CaptionSelect Closed Captioning control Cable Tuning Channel Memory AUTO-PROGRAMMING Select Channel MemoryPress the Menu button to turn Press the Status or Menu MADD/DELETE Channels Select Channel MemoryPress the Menu button to Press the Status or MenuSET Clock Select SET Clock controlPress the remotes number buttons to set the time clock Half Hour ReminderSET Alarm Timer Sleep TimerParental Control Setup Code Number Enter a new four digit number code using the remoteFirst lets set your Parental Code Select the Parental CON- TrolParental Control Channel Blocking Select the Channel Blocking controlPress Channel Content Advisory Select the Content AdviParental Control Enter the correct ParentalContent Advisory Movie Ratings Select the Movie Ratings Menu optionSelect the desired Movie Blocking levelContent Advisory Parental Guidelines Select the Parental Guidelines Menu optionContent Advisory Blocking Options Review SettingsSelect the Blocking Options Menu controlChannel Display Select Channel Display controlLanguage Select the Language DIS- Play controlSound Menu Control Adjustments BASS, TREBLE, BalanceSelect BASS, or TREBLE, or Press the + or buttons toSound Menu Control StereoSelect Stereo sound control Second Audio ProgramDisplay Volume Select Display Volume controlSound Menu Controls Incredible StereoTV Speakers Connect the Right and Left Variable Audio OUT jacksSurround Sound Place the speakers so the viewVariable Audio Output Using the AUDIO/VIDEO Input Jacks AUX 1 Video InputsConnect the Video OUT jack Connect the Audio OUTAUX1 S-VIDEO Inputs Connect the S-VIDEO S- VHS OUT jack from the VCR toComponent Video Inputs Connect the Component Y PBSelect the AUX 1 Y PB PR Picture Source control on the TV Using the AUDIO/VIDEO Output Jacks AUDIO/VIDEO OutputsRemote Control Operation Smart PictureHighlighted in red Press the Menu M or butChannel SURF/SMART Surf Setting the TV Remote to Work Accessory Devices Setting the TV Remote to Work Accessory Devices Contin Direct Access MethodSetting the Remote to Work Other Devices Search Search MethodDevice. Point the remote toward Surf and the desired SystemRemote Control Direct Entry Codes for Accessory Devices VCR Brand Remote Code noDVD Brand Remote Code no Using the Remotes VCR Buttons Rewind ButtonSupplied by a VCR or other Connect the Video OUTMove to the next page after Set the TVs PIP Source Select control to AUX1 Video Press the Menu and Menu M buttons toSelect the channel on the VCR to view in the PIP window Press the PIP ON/OFF button on the remoteUsing PIP with the Remote Control Press the PIP ON/OFF button to show the PIP picturePress the PIP Size button to change the size of the PIP win Selecting the Picture Source for PIP PIP SourceSelect PIP Source control Adjusting Picture -IN -PICTURE Color and Tint PIP Color / PIP TintSelect PIP Color or PIP Press the + and buttons toFirst use an optional signal More PIP ConnectionsTV Help Menu Select Help on the TVs Main Menu Press the remotes MenuTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty