Hooking Up the TV/VCR, Rod Antenna | Philips CCC 190AT, CCC192AT

6 Hooking Up the TV/VCR

1

Hook up your TV/VCR using one of the connections shown.

A.

Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna

Connect a Cable signal or an antenna to the ANT(enna) Jack.

CCC130

ANT.

ANT.

B.

Hooking Up Your TV/VCR With a Cable Box

To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box.

C.

Hooking Up Your TV/VCR With an Indoor Antenna

To install a rod antenna (not sup- plied), push the stem of the antenna into the antenna hole on the top of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its length, direction, and angle for the clearest picture.

Connect the Cable signal to the IN Jack on the Cable Box.

Connect an RF coaxial cable (75-
ohm, not supplied) to the OUT Jack
on the Cable Box and to the
ANT(enna) Jack on the TV/VCR.	OUT	IN

CCC130

RF coaxial cable

(not supplied)

ANT.

ANT.

Rod Antenna

(not supplied)

CCC130

ANT.

ANT.

Image 6

Philips CCC 190AT, CCC192AT Hooking Up the TV/VCR, Hook up your TV/VCR using one of the connections shown, Rod Antenna

Contents

Color TV with built-in VCR This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial No Introduction FeaturesSafety Precautions Declaration of Conformity Table of Contents TV/VCR Maintenance Battery SafetyUsing the Remote Control Replace the battery compartment lid RF coaxial cable Not supplied Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Rod Antenna Crooked Pin Straight Pin Hooking Up the TV/VCR cont’dBent pin Cable Plug Turning On the TV/VCR Press the Menu button. The screen shown below will appear Language Selection Press the Menu buttonSelect Language English Español Select KL To END Press Exit Automatic Channel Setup Wait for the TV/VCR to set up channels Repeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Programming of the channel you added or deleted will appear Setting the Clock Manual Clock SettingCable Box users must set the clock manually Month To Correct Press Clear To END Press Exit SET Manual Clock Time Date To END Press ExitSET Manual Clock Time Date Sunday To Correct Press Clear To END Press Exit VCR Program VCR Setup Caption Reminder Brightness Setting the Clock cont’dPRIM. Setup Press B Automatic PBS Channel Selection SET Auto Clock Time Date NOW Searching To END Press Exit NOW Searching flashes on the TV/VCR screenWait for the TV/VCR to find the time SET Auto Clock Time Manual PBS Channel Selection Use the Number buttons to select your PBS station Daylight-Savings Time PRIM. SETUP. Then, press the F.FWD/B buttonPRIM. Setup Press B VCR Program VCR Setup Press the PLAY/ button or the STOP/ button to select Time Zone Primary SetupVolume BAR SET Clock Select KL Choose B To END Press Exit Press the Menu button, then press the STATUS/EXIT button Front Panel ANTenna Jack AC Power CordRear Panel Connect your antenna or cable here. Details are on page six Remote Control Buttons REWind/ Button Menu ButtonSTATUS/EXIT Button STOP/ Button Adjusting the Picture Controls When you finish, press the STATUS/EXIT button Decrease Increase Adjusting the Picture Controls cont’dTint KK Sharpness TV Reset Decreased brightness If you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFF Reminder OFF Playing Follow the steps below to play a tapeInsert a tape in the TV/VCR To stop recording, press the STOP/ button Tape Speeds RecordingRead and follow the steps below to record a TV program Hrs Tape is in the TV/VCR. The record tab must be intact Length Press OTR Cancel Press ClearOne-Touch Recording Press the STOP/EJECT but- ton on the TV/VCR to stop the OTR TV/VCR is now in Line Input mode Rerecording Tape Duplication Timer Recording DailySelect Program Number To END Press Exit ONE Time Program Channel Time on Time OFF To Correct Press Clear To END Press Exit Timer Recording cont’d Program REVIEW, then press the F.FWD/B button Timer recording information for the program in the lowestWith the TV/VCR on, press the Menu button Gram Review and press the F.FWD/B button Follow the steps below to prevent accidental recording VCR Setup ONE Time PlayDefeat Recording REC Defeated Repeat Play VCR SETUP, then press the F.FWD/B buttonVCR Setup ONE Time Play Repeat Play on TV programming will appear while the tape is rewinding VCR Setup ONE Time Play Repeat Play A-B B Repeat PlayInsert a tape in the TV/VCR Press the Menu button Repeat Play cont’d Repeat Real-Time Counter Memory Appear on the screenStop Forward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPViewing a Still Picture SmartLock To block ratings, follow the steps belowSmartlock menu will appear SmartLock cont’d Ratings are defined onExample Specific Sub-ratings To change the access code, follow these steps After you enter the code, the Smartlock menu will appear Blocked Ratings TV-Y7 TV-G VCR Program VCR Setup Caption Reminder Blue Background Sleep Timer Timer during a recordingPress the SLEEP/WAKE UP button Wake Up Timer Timer Sleep Wake UP TV on ON-TIMETimer Sleep Wake UP Volume Bar VCR Program VCR Setup Caption Example To Adjust Press / B CaptionClosed Caption Menu Screen Closed Caption cont’d Standard Closed CaptionsHalf-screen text Automatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Specifications Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Page Supplied Accessories