Philips ISP1520

Philips Semiconductors ISP1520

Hi-Speed USB hub controller

Product data Rev. 03 — 24 November 2004 35 of 51

[1] For minimum value, the HS termination resistor is disabled and the pull-up resistor is connected. Only during reset, when both the hub

and the device are capable of high-speed operation.

[2] Characterized only, not tested. Limits guaranteed by design.

[3] In the suspend mode, the minimum voltage is 2.7 V.

Resistance

ZINP input impedance 10 - - MΩ

Termination

VTERM termination voltage for pull-up

resistor on pin RPU

[3] 3.0 - 3.6 V

Table 39: Static characteristics: USB interface block (DP0 to DP4 and DM0 to DM4)

…continued

= 3.0 V to3.6 V; T

amb

−

Cto+70

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Contents

Main ISP1520 Hi-Speed Universal Serial Bus hub controller Universal Serial Bus Specication Rev.2.0 Rev. 03 24 November 2004 Product data 1. General description 2. Features Universal Serial Bus Specication Rev.2.0 3. Applications 4. Abbreviations 5. Ordering information Product data Rev. 03 24 November 2004 4 of 51 6. Block diagram Fig 1. Block diagram. ISP1520 Philips Semiconductors ISP1520 Product data Rev. 03 24 November 2004 5 of 51 7. Pinning information ISP1520BD Fig 2. Pin conguration. 7.2 Pin description 7.1 Pinning Page ISP1520 Hub Demo Board Users Guide Page 8. Functional description 8.3 Phase-locked loop clock multiplier 8.4 I2C-bus controller 8.5 Overcurrent detection circuit 8.6 GoodLink 8.7 Power-on reset Fig 4. External clock with respect to power-on reset. Fig 3. Power-on reset timing. Stable external clock is to be available at A. POR EXTERNAL CLOCK A 9. Conguration selections 9.1 Conguration through I/O pins Page Philips Semiconductors ISP1520 9.2 Device descriptors and string descriptors settings using I2C-bus The I C-bus specication Page 9.2.3 ROM or EEPROM map Page Page Philips Semiconductors ISP1520 Page 10. Hub controller description 11. Descriptors Page Page 12. Hub requests Tab le 23 shows the suppor ted standard USB requests. 12.1 Standard USB requests 12.2 Hub class requests Tab le 24 shows the hub class requests. 12.3 Detailed responses to hub requests Page Page 12.4 Various get descriptors bmRequestType 10000000B bmRequest GET_DESCRIPTOR = 6 13. Limiting values 14. Recommended operating conditions In accordance with the Absolute Maximum Rating System (IEC 60134). 15. Static characteristics Page Page 16. Dynamic characteristics C; test circuit Figure 21; unless otherwise specied. Page TPERIOD is the bit duration corresponding with the USB data rate. Fig 11. Source differential data-to-EOP transition skew and EOP width. TPERIOD is the bit duration corresponding with the USB data rate. tJR is the jitter reference point. Fig 13. Receiver SE0 width tolerance. Fig 12. Receiver differential data jitter. Fig 14. Hub differential data delay and SOP distortion. Fig 15. Hub EOP delay and EOP skew. and T within recommended operating range; V 5 V; V =V ; V 17. Application information 17.1 Descriptor conguration selection ISP1520 Fig 18. Adjusting analog overcurrent detection limit (optional). ISP1520 17.3 Self-powered hub congurations ISP1520 Fig 19. Self-powered hub; individual port power switching; individual overcurrent detection. Fig 20. Self-powered hub; ganged port power switching; global overcurrent detection. ISP1520 18. Test information DMn D Fig 22. Full-speed test circuit. Fig 21. High-speed transmitter and receiver test circuit. 19. Package outline LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm SOT314-2 Fig 23. LQFP64 package outline. c 20. Soldering 20.1 Introduction to soldering surface mount packages Data Handbook IC26; Integrated Circuit Packages 20.2 Reow soldering 20.3 Wave soldering 21. Revision history Contact information 22. Data sheet status 23. Denitions 24. Disclaimers 25. Licenses 26. Trademarks Contents