Philips KX-PNBC8 4.3.2 For Windows NT 4.0

49

4.3.2 For Windows NT 4.0

Windows NT 4.0 comes with TCP/IP and

lpr

capabilities but they must be installed

when the unit is conﬁgured. You must install the TCP/IP Protocol, Simple TCP/IP

Services, and Microsoft TCP/IP Printing prior to entering the network printer on the

workstation.

Note: Once you have

lpr

installed on a Windows NT Server workstation and have

allowed printer sharing, other workstations may use the printer through the

Microsoft Windows Network without having to have separate

lpr

queues installed

on each workstation.

Setting Up the Network Card

The IP address, Subnet Mask and Default Gateway are required to be set for the

Network Card. If the value can be set using the printer LCD panel, refer to

When

Setting by Direct Entering in Step 1

on page 19.

This can be done with MAP if you have a NetWare connection on your network. F ollow

the instructions for these programs which are documented elsewhere. If you cannot

use these programs, you can use the ARP procedure program.

1. Install the Network Card in your printer.

2. Turn ON the printer.

Note: If you want to conﬁrm the MAC ADDRESS after setting up the Network Card, print

out the KX-P8415 Conﬁguration Page.Instructions on how to print the

Conﬁguration Page, refer to the “KX-P8415 Setup Guide and Reference Guide”.

It should show that TCP/IP is enabled but that the Protocol address is not

conﬁgured.

If the unit already has an IP address, these procedures will not work. However,

you can use the HTML pages accessed by MAP or Web Browser to change the IP

parameters.

Contents

Main Trademarks Important Copyright Notice Contents Chapter 5 Printing via the Server Computer (Windows 95/Windows 98/Windows NT 4.0) Chapter 6 Using the Management Access Program or a Standard Web Browser Chapter 7 NetWare Configuration Page Chapter 1 Introduction 1.1 What's in Your Package 1.2 Hardware/NOS Requirements Chapter 2 Installing the Network Card 2.1.2 Print Server Name of the Network Card 2.1.1 MAC ADDRESS and Serial Number 2.1 Important Note 2.2 Network Card Installation 1. Turn OFF the printer. 2. Remove the two screws and the Ethernet cover. Page Page Chapter 3 Before Starting the Setup 3.1 Selecting the Print Data Transfer Method 3.1.1 When Printing Directly from a Computer 3.1.2 When Printing via the Server Computer Chapter 4 Printing Directly from a Computer (Windows 95/Windows 98/Windows NT 4.0) 4.1.2 Step 4: Step 3: When Setting from the DHCP Server When Setting from the DHCP Server in Step 1 When Setting by Direct Entering in Step 1 When Setting by Direct Entering 4.1.2 Step 2:Setting Up the TCP/IP Protocol in the Network Card When Setting from the DHCP Server in Step 1 6.5 4.1.3 When Setting by Direct Entering in Step 1 Page Page Page Page 4.1.3 Step 3:Installing and Setting Up the IP Peer-to-Peer Windows Redirector Introduction and Preparation Page Page IP Peer-to-Peer Setup Page Page Page Page 4.1.4 Step 4:Setting Up the Printer Driver and the Printer Port Page Page Page Page Page Page Page 4.2 IPX Peer-to-Peer Printing Step 1: 4.2.2 Step 3: Step 2: Introduction and Preparation Page IPX Peer-to-Peer Setup Page 4.2.3 Step 3:Setting Up the Printer Driver and the Printer Port Page Page 4.3 LPR Printing 4.3.1 For Windows 95/Windows 98 Loading the lpr Spooler Setting up the Network Card 1. Install the Network Card in your printer. 2. Turn ON the printer. Page 4.3.2 For Windows NT 4.0 lpr Setting Up the Network Card When Setting by Direct Entering in Step 1 1. Install the Network Card in your printer. 2. Turn ON the printer. Page Page Chapter 5 Printing via the Server Computer (Windows 95/Windows 98/Windows NT 4.0) 5.1 IP Peer-to-Peer Printing 5.1.1 Step 5:Sharing the Printer Port on the Server Computer Page Page Page 5.1.2 Step 6:Setting Up the Printer Driver and the Printer Port on the Client Computer Page Page Page Page Page Page Page Page Page Page Page 5.2 IPX Peer-to-Peer Printing 5.2.1 Step 4:Sharing the Printer Port on the Server Computer Page Page 5.2.2 Step 5:Setting Up the Printer Driver and the Printer Port on the Client Computer Page Page Page Page Page Page Page Chapter 6 Using the Management Access Program or a Standard Web Browser 6.1 Where to Place the MAP Utility 6.2 How to Install MAP in Windows 6.3 Using the MAP Program 6.4 Web IP Browser 6.5 Dynamic Host Conguration Protocol not enabled ON enabled OFF 6.6 Windows Internet Name Service (WINS/DHCP) 6.6.1 Using WINS with your Print Server 6.6.2 Conguring for the WINS Server Page Chapter 7 NetWare Conguration 7.1 Conguring NetWare 3.x 7.1.1 Start PCONSOLE and Select File Server 7.1.2 Create Print Queues 7.1.3 Enter the Print Server Name 2.1.2 Page 7.1.4 Congure the Print Server 7.1.5 Assign Print Queues to the Printer 7.1.6 7.1.6 Set Up Notify Options for the Printer 7.1.7 Installing the Print Server on Multiple File Servers 7.1.8 Primary File Server 7.1.9 Preferred File Servers 7.2 Conguring NetWare 4.x 7.2.1 Conrm Bindery Context 7.2.2 Congure in Bindery Mode with PCONSOLE Page 7.3 Conguring NetWare 5 7.3.1 When using IPS/SPX protocol 7.4 7.3.2 When using TCP/IP protocol 7.3.3 NDPS Method (Using PServer Method) Page Page Page Page Page Page Page Page Page Page 7.3.4 NDPS Method (Using UNIX Method) Page Page 7.4 Conguring the Network Card in NetWare Directory Services object 7.5 7.3 enterprise 7.4.1 Create Printer Object 7.4.2 Create Print Server Object 7.4.3 Create Print Queue Object not Page Page Page Page Page 7.5 Network Card Conguration 7.1.9 whole typed whoami typeless Page 7.6 Using the Novell PCONSOLE Utility 7.6.1 Changing the File Server 7.6.2 Changing Print Queues 7.6.3 How to Set Up Notify (NetWare 3.x Bindery mode only) Page Page Page Page 8.3 Resetting the Print Server to Factory Default 8.4 How to Diagnose Problems 8.1 8.2 8.5 Troubleshooting Checklists for the NetWare Protocol NetWare Checklist 2.1.1 File Server Checklist Workstation Checklist Network Card Conguration Checklist Printer Server/File Server/Printer Checklist Workstation to Network Card Connection Checklist Network Card Loses Its File Server Connection Unable to Print from a Different Context Appendix A Jumper Settings A.1 Network Card and Jumper Locations A.2 Reset to Factory Appendix B Specications B.1 Network Card B.2 Network Cable Numerics Index I , L J M N P R S T U W