Picture Select | Philips VR400BMG instruction

36 Picture Select

This function enables you to select the picture quality of a tape.

Make sure:

●The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once.

●There is a tape in the VCR.

During tape playback, press the MENU button until the main menu appears.

- M E N U -		POWER		VCR/TV EJECT
TIMER PROGRAMMING		1	2	3
AUTO REPEAT	[OFF]

BPICTURE SELECT

CHANNEL SET UP	4	5	6
CLOCK SET	4	5	6
CLOCK SET
LANGUAGE SELECT
AUTO SATELLITE LINK	7	8	9	CHANNEL
	7	8	9
2	SPEED	0	+100
	SLOW	QUICK-	SEARCH
		QUICK-	TIME INDEX
		FIND	TIME INDEX

Press the PLAY button or the STOP button repeatedly to	1	MENU				3
select PICTURE SELECT. Then, press the F.FWD button.		MENU	DISPLAY	EXIT	COUNTER
select PICTURE SELECT. Then, press the F.FWD button.
3				RESET MEMORY
		REWIND	/ PLAY		F.FWD
		RECORD		/ STOP	PAUSE/STILL
With in five seconds, press the F.FWD button until your						2
desired mode (NORMAL, SOFT or SHARP) appears on
the screen.

Helpful Hint

•You may only set the Picture Select during tape playback.

Page 36

Image 36

Philips VR400BMG owner manual Picture Select, Press the Play button or the Stop button repeatedly to

Contents

VCR Warranty Verification For Customer Use Features Safety PrecautionsIntroduction Declaration of Conformity Table of Contents Before Using Your VCR Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenance Hookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TV Plug in the AC power cords of the TV and the VCR CH3 CH4 Cable Signal ConnectionsRecording/Viewing Any Channel Signal Recording One Channel/Watching AnotherCable Box/DBS Cable Hookups With a Stereo TV Turning on Your VCR Below will appear Automatic Channel Setup Press the Menu button until the main menu appears Automatic Channel Setup cont’d Adding/Deleting Channels Setting the Clock Follow the steps below to set your VCR’s clock. Make sure Setting the Clock cont’d Your selection will flash on the screen in the AM/PM space Press the Counter RESET/EXIT button to exit Language Selection OFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Remote Control Buttons Counter RESET/EXIT Button Eject ButtonTime Search Button Index Search Button VCR Display Panel Speed Button Power Button Remote Sensor FWD Fast Forward ButtonVCR/TV Button Play Button AC Power Cord Rear PanelVideo OUT Jack Video in Jack Playing VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording 1Turn on the TV Insert a tape One-Touch Recording Starting an OTRStopping an OTR Timer Recording Channels are set up Clock is set Timer Recording cont’d Repeat the procedure in to set the recording’s end timeEnter the recording’s start time Start Time END Time Channel REC Speed SLP Timer Recording cont’d Cancelling a Timer Recording Correcting a Timer Recording 42&5 Auto Satellite Link Using a Satellite Tuner Set the program to be recorded On the satellite tuner Press the VCR/TV button on the VCR remote control to Recording One Channel/Watching AnotherTo return to the channel being recorded, use the TV Put the VCR in VCR position. The VCR/TV light will appear Rerecording Tape Duplication Antenna Repeat Play Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still Picture Picture Select Press the Play button or the Stop button repeatedly toSelect Picture SELECT. Then, press the F.FWD button Real-Time Counter Memory Press the Play button to watch the tape Index Search Press the Index Search button Time Search Press the Time Search button Quick Find Press the QUICK-FIND buttonTo resume normal tape playback, press the Play button Automatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 or Specifications Renewed Index Supplied Accessories

Philips VR400BMG Picture Select, Press the Play button or the Stop button repeatedly to

Models: VR400BMG

36 Picture Select

+100

Press the PLAY button or the STOP button repeatedly to

select PICTURE SELECT. Then, press the F.FWD button.

Helpful Hint